Question

Notify Me Bookmark

a) Find the voltages at each of the nodes, A, B, C, D, E and F below. Use the following circuit parameters: Vdd = 5 V, Vtn = 0.5 V, |Vtp| = 1.5 V

a) Find the voltages at each of the nodes, A, B, C, D, E and F below. Use the following circuit parameters: Vdd = 5 V, Vtn = 0.5 V, |Vtp| = 1.5 V

Image text
a) Find the voltages at each of the nodes, A, B, C, D, E and F below. Use the following circuit parameters: Vdd = 5 V , V t n = 0.5 V , | V t p | = 1.5 V

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

We observe that NFETs do not transmit a ‘1’ very well and PFETs do not transmit a ‘0’ very well because with VGS = VDD and VDS = VDD in an NFET, the Source terminal will charge up only until it reaches VDD-VTn because at higher voltages, the Gate-Source voltage difference is less than the Threshold Voltage VTn of the NFET causing it to ‘turn-off’ when the Source Terminal rises to within a VTn of VDD. Sketch the output voltage characteristic if the PFET and the NFET positions were swapped as shown below? i) Write down the voltages at A, B, C, D, E, F, G in the following circuit, assuming that the initial voltage on each node is 2.5 volts. The relevant transistor parameters are, VDD = 5 V, VTn = 1 V and ∣VTp∣ = 0.7 V

We observe that NFETs do not transmit a ‘1’ very well and PFETs do not transmit a ‘0’ very well because with VGS = VDD and VDS = VDD in an NFET, the Source terminal will charge up only until it reaches VDD-VTn because at higher voltages, the Gate-Source voltage difference is less than the Threshold Voltage VTn of the NFET causing it to ‘turn-off’ when the Source Terminal rises to within a VTn of VDD. Sketch the output voltage characteristic if the PFET and the NFET positions were swapped as shown below? i) Write down the voltages at A, B, C, D, E, F, G in the following circuit, assuming that the initial voltage on each node is 2.5 volts. The relevant transistor parameters are, VDD = 5 V, VTn = 1 V and ∣VTp∣ = 0.7 V
Solution
0 0

Consider a CMOS inverter fabricated in a 0.25-um CMOS process for which VDD = 2.5 V, Vtn = -Vtp = 0.5 V, and unCox = 3.5upCox = 115 uA/V2. In addition, QN and QP have L = 0.25 ?m, and (W/L)n = 1.5. (a) Find Wp that results in VM = VDD / 2. What is the silicon area utilized by the inverter in this case? (b) For the matched case in (a), find the values of VOH, VOL, VIH, VIL, NML, and NMH. (c) For the matched case in (a), find the output resistance of the inverter in each of its two states.

Solution
1 0

Dynamic CMOS Circuits (a) During precharge (Clk=0), All inputs are logic 0 for the following Dynamic 3NAND. During evaluation (Clk=1), A is activated (0 → 1). Given VDD = 1.5 V, Vtn = 0.5 V, CL = 150 fF, C1 = 25 fF, and C2 = 50 fF, what is the final output voltage? (b) Calculate C1 of the following circuit so that the final voltage is determined by A input. CL = 175 fF, VDD = 1.5 V, and Vtn = 0.5 V. Assume that all inputs are logic 0 during the precharge. (c) i) Write the Boolean expression for OUT of the following circuit. ii) VDD = 2.0 V and Vtn = 0.5 V. During precharge (Clk = 0), All inputs are logic 0. During evaluation (C∣k = 1), A and B are activated (0 → 1). What is the final voltage when the evaluation mode settles?
Solution
0 0