Question

Notify Me Bookmark

A particular inverting circuit uses an ideal op amp and two 10-kΩ resistors. What closed-loop gain would you expect? If a dc voltage of +1.00 V is applied at the input, what outputs result? If the 10-kΩ resistors are said to be “1% resistors,” having values somewhere in the range (1 ± 0.01) times the nominal value, what range of outputs would you expect to actually measure for an input of precisely 1.00 V?

A particular inverting circuit uses an ideal op amp and two 10-kΩ resistors. What closed-loop gain would you expect? If a dc voltage of +1.00 V is applied at the input, what outputs result? If the 10-kΩ resistors are said to be “1% resistors,” having values somewhere in the range (1 ± 0.01) times the nominal value, what range of outputs would you expect to actually measure for an input of precisely 1.00 V?

Image text
A particular inverting circuit uses an ideal op amp and two 10-kΩ resistors. What closed-loop gain would you expect? If a dc voltage of +1.00 V is applied at the input, what outputs result? If the 10-kΩ resistors are said to be “1% resistors,” having values somewhere in the range (1 ± 0.01) times the nominal value, what range of outputs would you expect to actually measure for an input of precisely 1.00 V?

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

Measurement of a circuit incorporating what is thought to be an ideal op amp shows the voltage at the op-amp output to be -2.000 V and that at the negative input to be -1.000 V. For the amplifier to be ideal, what would you expect the voltage at the positive input to be? If the measured voltage at the positive input is -1.005 V, what is likely to be the actual gain of the amplifier?
Solution
0 0

You are provided with an ideal op amp and three 10-kΩ resistors. Using series and parallel resistor combinations, how many different inverting-amplifier circuit topologies are possible? What is the largest (noninfinite) available voltage gain magnitude? What is the smallest (nonzero) available gain magnitude? What are the input resistances in these two cases?
Solution
0 0

For the amplifier below, following design information is provided: VDD = 3.3 V, R = 2.4 kΩ, ISS = 1.8 mA, k1 = k2 = 5 mA/V2, VTH,1 = VTH,2 = 0.5 V, λ = 0.1 V−1, γ = 0, ki′ = μ0Cox, ki = μ0 Cox(W L)i. Assume that both transistors are identical and in the saturation region. Finally, NMOS and PMOS bulk terminals are connected to the ground and VDD, respectively. a) What is the DC bias voltage for M1 and M2 given that the voltage drop across ISS is 0.4 V ? You can neglect the channel length modulation, here. Check that the transistors are in the correct operation-mode. b) The resistors will be realized using identical PMOS transistors M3 and M4. If the transistors to be used will have k3 = k4 = 1.5 mA/V2, what will be their overdrive voltages? Check that the transistors are in the correct operation-mode. c) What is the differential voltage gain AV,diff = Vout/Vid in dB ? d) ISS will be realized as a cascode current source. Assume that the voltage drop of 0.4 V is equally shared by the two transistors, M5 and M6 having k5′ = k6′ = 0.5 mA/V2 and VTH, 5 = VTH, 6 = 0.5 V. Assuming the gate voltages of both transistors are 1 V, find the W/L ratios of each device. Once again, you can neglect the channel length modulation here. e) Considering (d), how would the W/L ratios qualitatively change (increase/decrease/stays the same), if γ > 0 ? Explain your reasoning analytically, i. e. , using appropriate equations. f) Using the cascode current source, calculate the common-mode gain of the circuit AV, CM = Vout /Vin in dB, where Vin . s applied to the gates of both M1 and M2. Assume λ = 0.1 V−1 for M5 and M6. g) Calculate the CMRR of the circuit in dB.
Solution
0 0