Question

Notify Me Bookmark

Consider an NMOS inverter. The NMOS has a W/L ratio of 2.22/1 and kn' = 100 μA/V2, VDD = 2.5 V, VT0 = 0.6 V. and the resistor is 28.8 kΩ. Assume that the load capacitor is 0.1 μF. What are the (a) Static Power Dissipation, (b) Dynamic Power Dissipation, (c) rise time, (d) fall time and (e) propagation delay.

Consider an NMOS inverter. The NMOS has a W/L ratio of 2.22/1 and kn' = 100 μA/V2, VDD = 2.5 V, VT0 = 0.6 V. and the resistor is 28.8 kΩ. Assume that the load capacitor is 0.1 μF. What are the (a) Static Power Dissipation, (b) Dynamic Power Dissipation, (c) rise time, (d) fall time and (e) propagation delay.

Image text
Consider an NMOS inverter. The NMOS has a W/L ratio of 2.22/1 and kn' = 100 μA/V2, VDD = 2.5 V, VT0 = 0.6 V. and the resistor is 28.8 kΩ. Assume that the load capacitor is 0.1 μF. What are the (a) Static Power Dissipation, (b) Dynamic Power Dissipation, (c) rise time, (d) fall time and (e) propagation delay.

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Login Sign Up

Similar/Related Questions

The circuit in Figure 1 is an NMOS switch circuit. Assume VDD = 5 V, γ = 0.4 V1/2, 2∣φf∣ = 0.6 V, VTO = 1 V, kn′ = 100 μA/V2, (W/L) = 10, and λ = 0.1 V−1. The channel length modulation is applicable only in the saturation region. a. Determine the charging current to CL right after the rising edge of the input. Assume that the capacitor is completely discharge at the beginning of the transition. Make sure that you include all applicable device parameters in your calculations. b. Determine the charging current to CL when the output voltage is at 50% of VDD. Again, make sure that you include all applicable device parameters in your calculation. c. Use the results from parts a and b to estimate the low-to-high propagation delay (tpLH) of the NMOS switch in Figure 1. d. Use PSPICE and measure the tpLH of the circuit in Figure 1 and compare your results with part c. (Hint: the .model for this device is shown below of this page)
Solution
1 0

Problem 3: (Short Circuit Power Consumption) For the circuit in Figure 2, assume that the input Vin is a periodic square wave signal (called "clock") of frequency 200 MHz, and has a rising transition time (from 0−100% of VDD ) of 0.2 ns and a falling transition time (from 100−0% of VDD ) of 0.2 ns. For the inverter in the figure, find the short circuit power consumption. Use the procedural hints listed below. Procedural Hints:Calculate the short circuit duration, tsc. Short circuit currents occur when both nMOS and pMOS transistors are simultaneously ON. Use the rise/fall times given. Calculate the peak short circuit currents. For simplicity assume that Ipeak_sc_LH and Ipeak_sc_HL are equal, and calculate the latter only. To calculate Ipeak_sc_HL, , assume that the short circuit current for the H-to-L transition peaks when Vin = VDD/2 and Vout = 9 VDD /10 (this is an arbitrary choice assumed for this problem alone). Now calculate the pMOS transistor current - this will be Ipeak_sc_HL. . Question: Does the nMOS current equal the pMOS current? If not, how do you account for InMOS−IpMO ? Using your results from (1) and (2), calculate the short circuit power dissipation. Note: Assume that VDD = 1.0 Volts, (W/L)p = 3.5 /0.1, and (W/L)n = 2 /0.1. Transistor properties are given by the 90 nm model parameters handout posted on the class web-site. For the current calculation, use the transistor parameters (not the equivalent resistance parameters) and ignore channel length modulation. Assume that there is an 89 fF load on Out.

Solution
0 0

Consider a CMOS inverter with Vdd = 3.3 V. Please be careful with units. The NMOS transistor has the following characteristics. The channel length is 20 nanometers. For NMOS, Oxide thickness = 5 Angstroms, Threshold Voltage = 0.12 V, mobility = 580 cm^2/V-sec, transistor W = 80 nm. For PMOS, all parameters are the same as NMOS except up = 220 cm2/N-sec. (a) (4pts) compute beta_n in units of [A/V^2]. (b) (4pts) compute the resistance Rn of the inverter. (c) (4pts) compute the resistance Rp of the inverter. (d) (4pts) what is the value of noise margin high (NMH) of the inverter? Assume the CMOS inverter has VDD = 3.3 V, VIL = 0.45 V, VIH = 0.92 V, VOL = 0.12 V and VOH = 2.9 V. (e) (4pts) compute the maximum operating frequency of the inverter when the rise and fall times are equal with a value of 0.1 ns each.
Solution
2 0