Question

Notify Me Bookmark

Consider the amplifier shown below. Transconductance of M1 is gm and there is no channel-length modulation. Assume the following parameters: RL = 5kΩ, gm = 2mS, RS = 1kΩ, C1 = 100fF, CL = 1pF. Calculate bandwidth (in MHz) of the amplifier using OCT. 24.1 MHz 12 MHz 32 MHz

Consider the amplifier shown below. Transconductance of M1 is gm and there is no channel-length modulation. Assume the following parameters: RL = 5kΩ, gm = 2mS, RS = 1kΩ, C1 = 100fF, CL = 1pF. Calculate bandwidth (in MHz) of the amplifier using OCT. 24.1 MHz 12 MHz 32 MHz

Image text
Consider the amplifier shown below. Transconductance of M1 is gm and there is no channel-length modulation. Assume the following parameters: RL = 5kΩ, gm = 2mS, RS = 1kΩ, C1 = 100fF, CL = 1pF. Calculate bandwidth (in MHz) of the amplifier using OCT. 24.1 MHz 12 MHz 32 MHz

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

The MOSFET in the common source amplifier is shown below. All the MOSFETs are identical. Assume negligible channel length modulation. VTn = +1 V, μ = 600 cm2/V⋅s, Cox’ = 0.23 μF/cm2, Cgs = 1 pF, and Cgd = 0.2 pF. (50pts) RS = 1 MΩ RG = 1 MΩ RD = 10 kΩ RL = 10 kΩ (i) Calculate the MOSFET W/L such that the bias current of M1 and transconductance of M1 are 1 mA and 5 mS, respectively. (ii) Find the mid frequency voltage gain in dB. (iii) Find the upper 3-dB frequency, fH. (iv) Find the value of CG, CS, and CD such that the corresponding poles are at 1 Hz, 100 Hz, and 10 Hz, respectively. (v) Write down all the zeros and poles of the overall amplifier (3 zeros and 3 poles for the lower frequency response and 1 pole for the higher frequency response). Sketch and carefully label the Bode plot for the gain magnitude (indicate the corner frequency and the slope). Specify the lower 3-dB frequency fL.
Solution
0 0

Question: For the AC equivalent circuit of a common-emitter BJT amplifier shown in Figure 1, assume that VCC = 10 V, VBE = 0.7 V, RS = 5 kΩ, RB = 100 kΩ, RL = 1 kΩ, Cb'e = 2 pF, Ccb′ = 1 pF, and CL = 1 pF. Assume bias current IB = 25 μA, Boltzmann's constant k = 1.38×10−23 J/K, q = 1.6 ×10−19 C, T = 300 K, VT = 26 mV, β = 100, rbb' = 100 Ω, and ignore ro. Assuming the equivalent noise bandwidth is 100 kHz, and neglecting the flicker noise and capacitive effect. Note: For the BJT biased on the forward active region: rπ = VT/IB, gm = IC/VT. (a) Calculate the total equivalent input rms noise voltage and current by looking into node a. (b) Calculate the total equivalent input rms noise voltage and current by looking into node b. (c) Discuss if a transformer (with turn ratio I:N) can be incorporated into point b to minimize the total input referred noise? If yes, what is the N to be? Figure 1
Solution
0 0

A common-source amplifier is shown below. The MOSFET parameters are k'n = 2mA/V2, VT = 0.8 V. The amplifier is biased with a source VDD = 5 V, and resistors RD = 4 kohm, RS = 1 kohm, RG1 = 225 kohm, RG2 = 175 kohm, Vov = 0.75 V (a) Calculate the drain current ID. Recall the formula for a MOSFET in saturation: ID = 1/2k'n(VGS - VT)2 (b) Obtain the MOSFET voltage vDS. (c) Using small-signal analysis, obtain the voltage gain vo/vi for RL = 12 kohm. Assume ro = 100 kohm, gm = 1 mA/V.

Solution
1 0