Question

Notify Me Bookmark

Consider the circuit shown in Fig. P1.13, where is a dc signal of 1 V. Taking into account only the channel charge storage, determine the final value of when the transistor is turned off, assuming half the channel charge goes to . You may use the parameters for the CMOS processes in Table 1.5.

Consider the circuit shown in Fig. P1.13, where is a dc signal of 1 V. Taking into account only the channel charge storage, determine the final value of when the transistor is turned off, assuming half the channel charge goes to . You may use the parameters for the CMOS processes in Table 1.5.

Consider the circuit shown in Fig. P1.13, where is a dc signal of 1 V. Taking into account only the channel charge storage, determine the final value of when the transistor is turned off, assuming half the channel charge goes to . You may use the parameters for the CMOS processes in Table 1.5.

Image text
Consider the circuit shown in Fig. P1.13, where is a dc signal of 1 V. Taking into account only the channel charge storage, determine the final value of when the transistor is turned off, assuming half the channel charge goes to . You may use the parameters for the CMOS processes in Table 1.5.

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

Consider MOSFET-based current source circuits shown below. Assume that the n-type MOSFET transistors follow the long-channel model with μnCox = 100 μA/V2 and Vth,n = 0.5 V. All the transistors have a fixed channel length L = 0.25 μm. The bias voltage VB1 is at 0.8 V. Assume that all transistors have no back-bias effect. (1) (2) (a) For a basic current source in Fig. (1), size the NMOS transistor M1's width ( = W1) so that it conducts a current of 1 mA when it operates in saturation region. You may assume λn = 0. (b) What is the minimum value of Vout for this circuit that keeps M1 in saturation region? (c) For a cascode current source in Fig. (2), assume that the transistor M2 has the same width with M1 you determined from part (a). Determine the value of VB2 that yields the lowest minimum VOUT keeping both M1 and M2 in saturation regions. (d) Now, let's assume that the transistors M1 and M2 have a finite output resistance with λn = 0.1 V−1. Compute the value of the output resistance (Rout) of this cascode current source when M1 and M2 are in the saturation region. (Hint: Calculate the output impedance in a small signal equivalent circuit.)
Solution
0 0

Consider the differential pair shown in Fig. 1. The power supply voltage is VDD 5 V, and all transistors have μnCox = 100 μA/V2, W/L = 2 and Vt = 1 V. You may neglect channel length modulation (VA = 1). (a) What is the value of VGS for M1 and M2 when no differential input voltage is applied and both transistors are in saturation? (b) What is maximum common mode input voltage (hint: all transistors must remain in saturation for normal operation)?
Solution
0 0

For the circuit shown in Figure 2, VDD = 5 V, and transistors M1 and M2 have properties µnCox = 200µA/V2, (W/L) = 10, Vt0 = 0.7 V, and λ = 0. You may neglect the body effect below, unless you are specifically asked to consider it. Figure 2. Circuit for Problem 2. a) Draw the circuit above, and label the drain, gate, source, and bulk nodes for both transistors, using labels VD1, VG1, VS1, and VB1 for the drain, gate, source, and bulk nodes of device M1, respectively, and similarly for M2. In total, there should be 8 labels in your schematic. For this part, assume the transistors are in saturation. b) Determine the valid input range for the circuit under consideration; that is, determine the range on the input voltage Vin such that transistors M1 and M2 are operating in the saturation region. Note that, in your analysis, you are not constrained to Vin values between 0 V and VDD, inclusive; e.g., if Vin = 100 V keeps both of the transistors in saturation, then Vin = 100 V should be included in your range of valid input voltages. Your answer to this part should take the form Vin,low ≤ Vin ≤ Vin,high ; hopefully, it is obvious that you are being asked to provide numerical answers for the lower- and upper-bounds Vin,low and Vin,high , respectively. c) For the valid input range that you determined in part (b), determine the corresponding output voltage range; that is, determine Vout,low ≤ Vout ≤ Vout,high when the input is constrained to Vin,low ≤ Vin ≤ Vin,high. . As before, you should report numerical values for the lower- and upper-bounds Vout,low and Vout,high, , respectively. d) Determine the "on voltage" VON2 (or, as in the Sedra/Smith textbook, the "overdrive voltage") and drain current ID2 of transistor M2 over the range of valid input voltages. Also, determine the drain current ID1 of M1 over the valid input range. e) If you were to consider it, would any of the transistors in the circuit above be affected by the body effect? If "yes," then list the device (or, devices, as the case may be). Qualitatively speaking, how would your answers to parts (b) and (c) change if you were to take the body effect into account? Explain your reasoning.
Solution
0 0