Question

Notify Me Bookmark

Consider the Common Emitter Amplifier shown below. Determine the voltage gain AV. The first step to solve this problem is to find the operating point. Assume VT = 26 mV and VBE ≈ 0.7 V A. −75.5 V/V B. −62.3 V/V C. −83 V/V D. −154 V/V

Consider the Common Emitter Amplifier shown below. Determine the voltage gain AV. The first step to solve this problem is to find the operating point. Assume VT = 26 mV and VBE ≈ 0.7 V A. −75.5 V/V B. −62.3 V/V C. −83 V/V D. −154 V/V

Image text
  1. Consider the Common Emitter Amplifier shown below. Determine the voltage gain A V . The first step to solve this problem is to find the operating point. Assume V T = 26 m V and V B E ≈ 0.7 V A. − 75.5 V / V B. − 62.3 V / V C. − 83 V / V D. − 154 V / V

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

For the diode circuit shown, what is the output voltage, Vo, in millivolts? Assume that 11 = 15xI2, and the junction area of D2 is 20x as as large as the junction area for D1. Use Vt = kt/q = 26 mV. (Hint: You don't need to know the values for Vcc, I1, I2 or for Is1, Is2. All you need to solve this problem is the ratios given!)
Solution
0 0

Multistage Amplifier In this last question, you are going to design a 2-stage amplifier. The first stage is a common-source amplifier and the second is a source follower, as shown in the figure below: Some parameters you may use are: VDD = 5 V, μnCox = 0.2 mA/V2, μpCox = 0.1 mA/V2, λn = 0.06, λp = 0.03, γ = 0, VTHN = 0.7 V, VTHP = −0.6 V; allow RL = 2 KΩ. Note: CS is large enough so that it will act as a short circuit for frequencies of interest. The circuit should satisfy the following specs: Total power consumption = 6.5 mW (use this spec to find total current drawn from VDD) The ratio of power consumed by the biasing branch: the amplifier: the follower stage should be 1:2:10 CS stage should provide a gain equal to −40 V/V Source follower stage should have a gain of 0.6 V/V Vomax = 3.8 V Find the W/L of all transistors and value of RD. Make reasonable simplifications.
Solution
0 0

Electronics 2 - Homework 2 Second semester 2023-2024 Solve the following questions, and verify your solution using LTSpice. simulation. For each question you need to:Solve the question by handProvide a screenshot of the circuitProvide a screenshot confirming the hand calculations Note that you can change the BJT parameter Beta by adding a SPICE directive and changing the parameter BF Question 1: BJT transistors The parameters for each transistor in the figure below are β = 80, and VBE(m) = 0.7 V. Determine all the voltages and currents in the circuit. Circuit for question 1 Question 2: Amplifier Configurations The signal source in the circuit below is vs = 5 sin⁡(100000πt)mV. The transistor parameters are β = 120, and the capacitors are 10 μF (a) Design the circuit such that IC = 0.25 mA and VCE = 3 V. (b) Find the open circuit voltage gain Avo (c) Find the input resistance Rin (from the base of the transistor) (d) Find the output resistance (e) Use the amplifier model (Avo, Rin, Ro) to find vo(t). Circuit for question 2 Question 3: Amplifier Configurations Consider the circuit shown. The transistor current gain β = 180. and the source signal has a frequency of 100 kHz and the capacitors are 10 μF Note that the current source is replaced by an open circuit in the small signal model equivalent circuit. Determine: (a) the voltage gain from source to load, (b) the input resistance seen by the source (c) the output resistance

Solution
0 0