Question

Notify Me Bookmark

Design the following complete addition circuit using the LT Spice program. You can get NMOS and PMOS channel lengths (I) 0.2μm. a) Derive the truth table of the circuit. b) Show that the circuit performs full additive function by performing DC operating point analysis and Transient analysis.

Design the following complete addition circuit using the LT Spice program. You can get NMOS and PMOS channel lengths (I) 0.2μm. a) Derive the truth table of the circuit. b) Show that the circuit performs full additive function by performing DC operating point analysis and Transient analysis.

Image text
Design the following complete addition circuit using the LT Spice program. You can get NMOS and PMOS channel lengths (I) 0.2μm. a) Derive the truth table of the circuit. b) Show that the circuit performs full additive function by performing DC operating point analysis and Transient analysis.

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

Design an inverter circuit as shown below. You can set the supply voltage (VDD) to 3V. You can get NMOS and PMOS channel lengths (I) 0.2µm. Take the following parameters into consideration when adjusting NMOS and PMOS channel widths (w). 1. Set the threshold value (VTH) = 1.5 V. 2. Delay from 50% to 50% when driving 50fF load = T = 7 × 1ps a) Show that the numerical threshold value is 1.5 V by performing a DC sweep. b) Show the operation of the circuit and the delays with transient analysis. Note: You can take 100MHz as the input signal frequency. Do it using the It spice program and explain it to me step by step, including showing the entry points of the values.
Solution
0 0

A full-adder is a basic combinational block used to build complex digital circuits. It is basically a 1-bit adder, that computes the sum S and output carry Cout of two input bits, A and B, plus the initial input carry Cin. The truth table of the full-adder is shown below. Cin A B S Cout 0 0 0 0 0 0 0 1 1 0 0 1 0 1 0 0 1 1 0 1 1 0 0 1 0 1 0 1 0 1 1 1 0 0 1 1 1 1 1 1 1. Derive the logic functions for S and Cout. Use only AND, OR, and negation operators in your expressions. You can use whatever method you like (boolean algebra, Karnaugh maps, etc.). 2. Implement both of the functions as static CMOS logic gates (at most followed by an inverter). Draw the transistor-level schematics. You can assume that both the direct and negated versions of each input are available. 3. Size all the devices in the pull-up (PU) networks of your gates, so that the equivalent resistance of each PU is the same as that of a PMOS with W/L = 2. Repeat for the pull-down (PD) networks and a reference NMOS with W/L = 1. When you size a transistor network, you should always consider the input logic values that yield the worst-case equivalent resistance. Neglect the effect of internal node capacitances.
Solution
0 0

Consider the circuit shown above right. Here, you will use the following NMOS and PMOS models. You can import them into LTSpice a. Determine W2 such that an input DC level of 0.75 V yields an output DC level of 1 V. What is the low-frequency voltage gain under these conditions? Use AC analysis in SPICE to view the gain vs. frequency response of the amplifier. b. What is the change in the gain if the width and length of NMOS and PMOS devices varies by ±10% individually? Which one is the most sensitive? c. Establish a simulation setup to simulate the output resistance of the amplifier. What is the simulated value of the output resistance?
Solution
0 0