Question

Notify Me Bookmark

Determine gain for each of four amplifiers having current source load. Consider rO's each amplifier.

Determine gain for each of four amplifiers having current source load. Consider rO's each amplifier.

Image text
Determine gain for each of four amplifiers having current source load. Consider r O 's each amplifier.

Detailed Answer

2 0

Please enter your email here. You will get email when this question is answered by our tutor.

Answer
Doubtrix Logo

This Problem has been solved!

You'll get a detailed, step-by-step and expert verified solution.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Login Sign Up
  • Student Reviews:
  • (2)
  • Correct answers (2)
  • Complete solution (2)
  • Step-by-step solution (2)
  • Fully explained (2)

Similar/Related Questions

Electronics 2 - Homework 2 Second semester 2023-2024 Solve the following questions, and verify your solution using LTSpice. simulation. For each question you need to:Solve the question by handProvide a screenshot of the circuitProvide a screenshot confirming the hand calculations Note that you can change the BJT parameter Beta by adding a SPICE directive and changing the parameter BF Question 1: BJT transistors The parameters for each transistor in the figure below are β = 80, and VBE(m) = 0.7 V. Determine all the voltages and currents in the circuit. Circuit for question 1 Question 2: Amplifier Configurations The signal source in the circuit below is vs = 5 sin⁡(100000πt)mV. The transistor parameters are β = 120, and the capacitors are 10 μF (a) Design the circuit such that IC = 0.25 mA and VCE = 3 V. (b) Find the open circuit voltage gain Avo (c) Find the input resistance Rin (from the base of the transistor) (d) Find the output resistance (e) Use the amplifier model (Avo, Rin, Ro) to find vo(t). Circuit for question 2 Question 3: Amplifier Configurations Consider the circuit shown. The transistor current gain β = 180. and the source signal has a frequency of 100 kHz and the capacitors are 10 μF Note that the current source is replaced by an open circuit in the small signal model equivalent circuit. Determine: (a) the voltage gain from source to load, (b) the input resistance seen by the source (c) the output resistance

Solution
0 0

Cascode Stage. Design a Cascode amplifier shown in figure below to achieve a gain of 1600. Assume VDD = 1 V, Vth = 0.3 V, λn = 0.2 V−1, γ = 0, μnCox = 100 μA/V2, I1 = 1 mA, gmro ≫ 1. a) Find bias point (VGS−Vth of transistors) to achieve the target gain such that we achieve maximum swing at Vout. b) Find W/L for each transistor. c) Calculate optimal Vb and VIN DC bias to maximize output swing. What is this maximum/minimum voltage levels at the output? What is the maximum swing? d) Notice you must generate a specific Vb externally to maximize the swing. If a lazy designer decides to connect Vb to VDD instead, what would be the swing in this case? e) To realize the current source load, we will use a PMOS active load. For PMOS, use the same parameters with λp = 0.2 V−1, μpCox = 50 μA/V2. Assume the bias current will remain at 1mA, find the new gain value. What would be the W/L for PMOS if we want to have a VOD(VGS−Vth) of 0.1V for this device. f) Repeat part (e) for a PMOS load with 2L gate length. g) It seems like making the PMOS load very large (large W) is beneficial to reduce VOD and consequently improving the voltage swing. What do you think is the drawback?
Solution
0 0

Figure Q2 shows a BJT differential amplifier stage that uses a tail resistor, RO, to provide a bias current, IQ. Transistor parameters are VBE(on) = 0.7 V, β = 100, and VA = ∞. Also, Vcc = 15 V, −VEE = −15 V, RO = 56 kΩ, and RC = 15 kΩ. Figure Q2: Differential Amplifier (a) To calculate the transistor Q-points, what are the values you would assume for vB1 and vB2 ? (b) Determine the bias currents, IC1 and IC2, of the amplifier. (c) For a single-sided output, determine the differential-mode voltage gain (Ad), the commonmode voltage gain (Acm), the differential input impedance (Rid), the common-mode input impedance (Ricm), and the common-mode rejection ratio (CMRR) in dB for the differential amplifier. Assume a signal source resistance of 50 Ω on each input. (d) Will changing RC affect the amplifier CMRR? (e) Suggest two changes to this amplifier each of which would allow the CMRR to be increased. For each, give a reason why the change would have the desired effect.

Solution
0 0