Question

Notify Me Bookmark

Draw the CMOS transistor schematic for OAI22. Find width for the transistors such that it has roughly equal rise and fall times and has a worst-case pull-down resistance approximately equal to the effective channel resistance of a unit nMOS. b) Consider the Boolean equation for your gate. Find a set of inputs b, c, and d such that y = a(bar).

Draw the CMOS transistor schematic for OAI22. Find width for the transistors such that it has roughly equal rise and fall times and has a worst-case pull-down resistance approximately equal to the effective channel resistance of a unit nMOS. b) Consider the Boolean equation for your gate. Find a set of inputs b, c, and d such that y = a(bar).

Image text
Draw the CMOS transistor schematic for OAI22. Find width for the transistors such that it has roughly equal rise and fall times and has a worst-case pull-down resistance approximately equal to the effective channel resistance of a unit nMOS. b) Consider the Boolean equation for your gate. Find a set of inputs b, c, and d such that y = a(bar).

Detailed Answer

1 0

Please enter your email here. You will get email when this question is answered by our tutor.

Answer
Doubtrix Logo

This Problem has been solved!

You'll get a detailed, step-by-step and expert verified solution.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Login Sign Up
  • Student Reviews:
  • (1)

Similar/Related Questions

Assumptions for all problems (unless specified otherwise, give answers to 10% ): VDD(V) VT0( V) Body effect γ(V 0.5 ) VDSAT( V) k’ (A/V 2) λ(V -1 ) NMOS 2.0 0.4 0 0.5 500×10-6 0 PMOS -0.4 0 -0.5 -200×10-6 0 1. All transistors have the minimum length (Lunit = 250 nm) 2. Ignore body effect and channel length modulation 3. A transistor's intrinsic capacitance (cap) and gate cap are equal, i.e., Cint = Cg, γ = 1 4. The unit-sized transistor has Wunit = Lunit and intrinsic cap Cint = Cg = Cdb = Csb = 1.0fF. 5. For the unit sized inverter, β = (W/L)P / (W/L N = WP/WN = 2, WN = L = 250 nm 6. The unit sized transmission gate has a resistance Req,tr = 10kΩ and all caps of 1.0fF. a) (6 pts) How does the following circuit operate? In a few words/charts, describe what it does Sketch the waveforms of nodes X and Q given the inputs shown below. Initial state of signals X and Q are unknown (mark with xxx as needed) until the impact of the input signals propagate. X Q b) (4 pts) How would you size each transistor? Match the 2:1 inverter (including the clock). Draw the sizing next to the schematic. Calculate the switch model equivalent resistance(s) (note the equation given at the front of the exam for Req, switch model capacitance(s) (based on your sizing), and worst-case propagation delay through the circuit, max(tpLH,tpLH), where output is taken from Q and inputs are IN1 and IN2. c) (4 pts) Calculate the energy consumption from the VDD power supply of this circuit for the input pattern and time duration given in the timing diagram (previous page). Ignore the energy consumption related to driving IN1, IN2, and CLK. State any assumptions you need to make to determine a numerical value.

Assumptions for all problems (unless specified otherwise, give answers to 10% ): VDD(V) VT0( V) Body effect γ(V 0.5 ) VDSAT( V) k’ (A/V 2) λ(V -1 ) NMOS 2.0 0.4 0 0.5 500×10-6 0 PMOS -0.4 0 -0.5 -200×10-6 0 1. All transistors have the minimum length (Lunit = 250 nm) 2. Ignore body effect and channel length modulation 3. A transistor's intrinsic capacitance (cap) and gate cap are equal, i.e., Cint = Cg, γ = 1 4. The unit-sized transistor has Wunit = Lunit and intrinsic cap Cint = Cg = Cdb = Csb = 1.0fF. 5. For the unit sized inverter, β = (W/L)P / (W/L N = WP/WN = 2, WN = L = 250 nm 6. The unit sized transmission gate has a resistance Req,tr = 10kΩ and all caps of 1.0fF. a) (6 pts) How does the following circuit operate? In a few words/charts, describe what it does Sketch the waveforms of nodes X and Q given the inputs shown below. Initial state of signals X and Q are unknown (mark with xxx as needed) until the impact of the input signals propagate. X Q b) (4 pts) How would you size each transistor? Match the 2:1 inverter (including the clock). Draw the sizing next to the schematic. Calculate the switch model equivalent resistance(s) (note the equation given at the front of the exam for Req, switch model capacitance(s) (based on your sizing), and worst-case propagation delay through the circuit, max(tpLH,tpLH), where output is taken from Q and inputs are IN1 and IN2. c) (4 pts) Calculate the energy consumption from the VDD power supply of this circuit for the input pattern and time duration given in the timing diagram (previous page). Ignore the energy consumption related to driving IN1, IN2, and CLK. State any assumptions you need to make to determine a numerical value.

Assumptions for all problems (unless specified otherwise, give answers to 10% ): VDD(V) VT0( V) Body effect γ(V 0.5 ) VDSAT( V) k’ (A/V 2) λ(V -1 ) NMOS 2.0 0.4 0 0.5 500×10-6 0 PMOS -0.4 0 -0.5 -200×10-6 0 1. All transistors have the minimum length (Lunit = 250 nm) 2. Ignore body effect and channel length modulation 3. A transistor's intrinsic capacitance (cap) and gate cap are equal, i.e., Cint = Cg, γ = 1 4. The unit-sized transistor has Wunit = Lunit and intrinsic cap Cint = Cg = Cdb = Csb = 1.0fF. 5. For the unit sized inverter, β = (W/L)P / (W/L N = WP/WN = 2, WN = L = 250 nm 6. The unit sized transmission gate has a resistance Req,tr = 10kΩ and all caps of 1.0fF. a) (6 pts) How does the following circuit operate? In a few words/charts, describe what it does Sketch the waveforms of nodes X and Q given the inputs shown below. Initial state of signals X and Q are unknown (mark with xxx as needed) until the impact of the input signals propagate. X Q b) (4 pts) How would you size each transistor? Match the 2:1 inverter (including the clock). Draw the sizing next to the schematic. Calculate the switch model equivalent resistance(s) (note the equation given at the front of the exam for Req, switch model capacitance(s) (based on your sizing), and worst-case propagation delay through the circuit, max(tpLH,tpLH), where output is taken from Q and inputs are IN1 and IN2. c) (4 pts) Calculate the energy consumption from the VDD power supply of this circuit for the input pattern and time duration given in the timing diagram (previous page). Ignore the energy consumption related to driving IN1, IN2, and CLK. State any assumptions you need to make to determine a numerical value.
Solution
0 0

Use the Elmore delay approximation to find the worst-case rise and fall delays at the output for the following circuit. The gate sizes of the transistors are given in the figure. Use the assumption that the diffusion capacitance is equal to the gate capacitance, and that a minimum sized transistor has gate and diffusion capacitance equal to C. The resistance of an nMOS transistor with unit width is R and the resistance of a pMOS transistor with width 2 is also R. Also assume NO sharing of diffusion regions. (Hint: off-path capacitances can contribute to delay.)
Solution
0 0

Let's design CMOS logistic gate F(A, B, C, D) = A+(B∙C)+D For PMOS transistors and NMOS transistors of the same size, consider a fabrication process that is four times the resistance of the PMOS transistor. Assume that all diffusion areas have no sharing. Unit inverter refers to a minimum-sized inverter that makes rise resistance (also called pullup resistance) and fall resistance (also called pulldown resistance) equal by sizing the CMOS inverter shown in the following figure with PMOS:NMOS = 4:1. (a) Draw the transistor-level schematic of CMOS logic gate F consisting of PMOS and NMOS. (b) In the worst case scenario, size the PMOS and NMOS transistors of CMOS logic gate F to have the same rise and fall resistance as unit inverter. (c) Find the logical effect gA and intrinsic delay p of CMOS logic gate F with respect to Input A.
Solution
0 0