Question

Notify Me Bookmark

Explain the function of each transistor in the op amp shown in Figure 10.3.

Explain the function of each transistor in the op amp shown in Figure 10.3.

Image text
Explain the function of each transistor in the op amp shown in Figure 10.3.

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

3(a) A CMOS circuit is shown in Figure 4. Size the transistors in the circuit for more or less symmetrical delay under worst case conditions. Minimize the size as much as possible. Assume un = 2up. Show the size of each transistor in the diagram. Use a minimum transistor size of 10/2. (Note: Certain paths wont happen.) b) Redesign the circuit to minimize the number of transistors (you may use either pass logic or gate logic design).

Solution
0 0

The circuit shown in Figure 5-1 is a CMOS logic gate of some type. NOTE: Alternative symbols! a) Fill in the table below showing the state of each MOSFET (ON or OFF) and the output voltage for each combination of input states. [10] If 0 V represents a logic low, and +5 V represents a logic high, what is the logic gate function of this circuit? [2] c) Determine the output resistance ROUT of the CMOS gate of Figure 5-1 for each combination of inputs. [8] NOTE: ROUT is the Thevenin Resistance of the Gate. It is the total resistance connected between VDD and the output OR between the output and GROUND, depending on the state of the MOSFET switches. GIVEN : rDSn = 190 ohm and rDSp = 350 ohm d) If this gate exhibits a worst-case Low-to-High (tpLH) propagation delay of 60nsec when driving a given capacitive load, what would you expect the worst-case High-to-Low (tpHL) propagation delay to be?

The circuit shown in Figure 5-1 is a CMOS logic gate of some type. NOTE: Alternative symbols! a) Fill in the table below showing the state of each MOSFET (ON or OFF) and the output voltage for each combination of input states. [10] If 0 V represents a logic low, and +5 V represents a logic high, what is the logic gate function of this circuit? [2] c) Determine the output resistance ROUT of the CMOS gate of Figure 5-1 for each combination of inputs. [8] NOTE: ROUT is the Thevenin Resistance of the Gate. It is the total resistance connected between VDD and the output OR between the output and GROUND, depending on the state of the MOSFET switches. GIVEN : rDSn = 190 ohm and rDSp = 350 ohm d) If this gate exhibits a worst-case Low-to-High (tpLH) propagation delay of 60nsec when driving a given capacitive load, what would you expect the worst-case High-to-Low (tpHL) propagation delay to be?
Solution
1 0

Answer the following questions on the circuit shown in Fig. 3. The n-type MOS transistors M1 and M2 have the same characteristics, and the small-signal equivalent circuit of each transistor is shown in Fig. 4. Here, gm, ro, and v are the transconductance, the drain resistance, and the input voltage of the MOS transistor, respectively. RD and RS are the resistances in the circuit. VDD is a positive constant voltage. Note that v1, v2, v3, and v4 represent small-signal components of the voltages V1, V2, V3, and V4, respectively. (1) The small-signal components vin and vout represent the difference of two input signals v1 - v2 and the difference of two output signals v3 - v4, respectively. Find the voltage amplification factor A = vout/vin. (2) The small-signal components vin’ and vout’ represent the sum of two input signals v1 + v2 and the sum of two output signals v3 + v4, respectively. Find the voltage amplification factor A’ = vout’/vin’. (3) Describe in a few lines the function of the circuit in Fig. 3, based on the results of Parts (1) and (2). Assume ro → ∞ and RS ≫ gm-1.

Solution
0 0