Question

Notify Me Bookmark

Find the values of base, collector, and emitter currents in Q1 and Q2 for the circuit shown in Fig. 2(a). Assume, β = 80 and VBE = 0.7 V.

Find the values of base, collector, and emitter currents in Q1 and Q2 for the circuit shown in Fig. 2(a). Assume, β = 80 and VBE = 0.7 V.

Image text
Find the values of base, collector, and emitter currents in Q 1 and Q 2 for the circuit shown in Fig.2(a). Assume, β = 80 and V B E = 0.7 V .

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

Electronics 2 - Homework 2 Second semester 2023-2024 Solve the following questions, and verify your solution using LTSpice. simulation. For each question you need to:Solve the question by handProvide a screenshot of the circuitProvide a screenshot confirming the hand calculations Note that you can change the BJT parameter Beta by adding a SPICE directive and changing the parameter BF Question 1: BJT transistors The parameters for each transistor in the figure below are β = 80, and VBE(m) = 0.7 V. Determine all the voltages and currents in the circuit. Circuit for question 1 Question 2: Amplifier Configurations The signal source in the circuit below is vs = 5 sin⁡(100000πt)mV. The transistor parameters are β = 120, and the capacitors are 10 μF (a) Design the circuit such that IC = 0.25 mA and VCE = 3 V. (b) Find the open circuit voltage gain Avo (c) Find the input resistance Rin (from the base of the transistor) (d) Find the output resistance (e) Use the amplifier model (Avo, Rin, Ro) to find vo(t). Circuit for question 2 Question 3: Amplifier Configurations Consider the circuit shown. The transistor current gain β = 180. and the source signal has a frequency of 100 kHz and the capacitors are 10 μF Note that the current source is replaced by an open circuit in the small signal model equivalent circuit. Determine: (a) the voltage gain from source to load, (b) the input resistance seen by the source (c) the output resistance

Solution
0 0

In the amplifier circuit shown below, the BJT transistor has a β = 99 and the base emitter junction of the BJT when it is forward biased has a voltage drop of 0.7 V, i.e., VBE = 0.7 V. Consider that all three external capacitors shown in this circuit have very large values. Determine the DC values of the parameters shown in the Table below.
Solution
0 0

a. For the circuit shown below, show a clean and labeled small signal equivalent circuit and derive the expression for vo/vb, (vb is the small signal voltage at the base node) vo/vsig, Rin and Rout. (b) This is the design part. The specifications are as follows: The required gain vo/vb = −120 V/V, Ic = 1 mA. and the require voltage swing at the output is ±3 V around the DC value of the output. (Hint: Do not use the generic design rule. You should be able to find the DC voltages at the collector and emitter from the specifications). Assume Vcc = 8 V. For this design assume VA = ∞ (this makes ro = ∞), V T (Thermal Voltage) = 25 mV, VBE = 0.7 V, VCEsat = 0.3 V and β = ∞. Find the values of RC, RE, RB1, and RB2. (c) If the β = 100 instead of the design value, find the new Ic. Now assuming VA = 50 V find vo/vsig, Rout and RIN. For this part assume Rsig = 10 kΩ. Punt: If you could not answer (b), use RC = 3 kΩ, RE = 2 kΩ, RB1 = 50 kΩ, and RG2 = 30 kΩ (d) Run a transient simulation of the designed circuit in Multisim. Use the same BJT used in the lab simulation. Show the input voltage v sig and output voltage v o on the same plot. Choose vsig to be at 1 kHz and 10 mV peak sinusoidal. Compare with calculated value of the gain in part c.
Solution
0 0