Question

Notify Me Bookmark

For the circuit shown in the figure below, knowing that RE = 100 Ω, β = 100 and VA = ∞. The bias current IC = 0.3 mA. Calculate the output impedance Rout (Without any approximation) Rout = Ω Write 2 digits after the decimal point.

For the circuit shown in the figure below, knowing that RE = 100 Ω, β = 100 and VA = ∞. The bias current IC = 0.3 mA. Calculate the output impedance Rout (Without any approximation) Rout = Ω Write 2 digits after the decimal point.

Image text
For the circuit shown in the figure below, knowing that R E = 100 Ω , β = 100 and V A = ∞ . The bias current I C = 0.3 m A . Calculate the output impedance R out (Without any approximation )
R out = ◻ Ω
Write 2 digits after the decimal point.

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

For the circuit shown in the figure below, knowing that RC = 2.4 KΩ and VA = ∞. The input impedance Rin = 42.7 KΩ and the transconductance gm = 12 mS. find β. β =
Solution
0 0

a. For the circuit shown below, show a clean and labeled small signal equivalent circuit and derive the expression for vo/vb, (vb is the small signal voltage at the base node) vo/vsig, Rin and Rout. (b) This is the design part. The specifications are as follows: The required gain vo/vb = −120 V/V, Ic = 1 mA. and the require voltage swing at the output is ±3 V around the DC value of the output. (Hint: Do not use the generic design rule. You should be able to find the DC voltages at the collector and emitter from the specifications). Assume Vcc = 8 V. For this design assume VA = ∞ (this makes ro = ∞), V T (Thermal Voltage) = 25 mV, VBE = 0.7 V, VCEsat = 0.3 V and β = ∞. Find the values of RC, RE, RB1, and RB2. (c) If the β = 100 instead of the design value, find the new Ic. Now assuming VA = 50 V find vo/vsig, Rout and RIN. For this part assume Rsig = 10 kΩ. Punt: If you could not answer (b), use RC = 3 kΩ, RE = 2 kΩ, RB1 = 50 kΩ, and RG2 = 30 kΩ (d) Run a transient simulation of the designed circuit in Multisim. Use the same BJT used in the lab simulation. Show the input voltage v sig and output voltage v o on the same plot. Choose vsig to be at 1 kHz and 10 mV peak sinusoidal. Compare with calculated value of the gain in part c.
Solution
0 0

For the single-stage npn BJT amplifier circuit shown in Fig. Q8, the BJT Q1 has the following parameters: IS = 10−15 A, β = 100 and VA = 100 V. (a) What is the amplifier configuration? (2 marks) (b) Calculate the biasing DC collector current of BJT Q1, IC,Q1. (6 marks) (c) Calculate the AC small signal model parameters of BJT Q1. (3 marks) (d) Calculate the two port parameters, Gm, Rin and Rout . ( 5 marks) (e) Estimate the voltage gain (vout/vin ) of the amplifier. (4 marks)

Solution
0 0