Question

Notify Me Bookmark

For the differential amplifier of Fig. 9.15(a) let I = 0.2 mA, VCC = VEE = 1.5 V, VCM = −0.5 V, RC = 5 kΩ, and β = 100. Assume that the BJTs have VBE = 0.7 V at ic = 1 mA. Find the voltage at the emitters and at the outputs.

For the differential amplifier of Fig. 9.15(a) let I = 0.2 mA, VCC = VEE = 1.5 V, VCM = −0.5 V, RC = 5 kΩ, and β = 100. Assume that the BJTs have VBE = 0.7 V at ic = 1 mA. Find the voltage at the emitters and at the outputs.

Image text
For the differential amplifier of Fig. 9.15 (a) let I = 0.2 m A , V C C = V E E = 1.5 V , V C M = − 0.5 V , R C = 5 k Ω , and β = 100 . Assume that the BJTs have V B E = 0.7 V at i c = 1 m A . Find the voltage at the emitters and at the outputs. (a)

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

Figure Q2 shows a BJT differential amplifier stage that uses a tail resistor, RO, to provide a bias current, IQ. Transistor parameters are VBE(on) = 0.7 V, β = 100, and VA = ∞. Also, Vcc = 15 V, −VEE = −15 V, RO = 56 kΩ, and RC = 15 kΩ. Figure Q2: Differential Amplifier (a) To calculate the transistor Q-points, what are the values you would assume for vB1 and vB2 ? (b) Determine the bias currents, IC1 and IC2, of the amplifier. (c) For a single-sided output, determine the differential-mode voltage gain (Ad), the commonmode voltage gain (Acm), the differential input impedance (Rid), the common-mode input impedance (Ricm), and the common-mode rejection ratio (CMRR) in dB for the differential amplifier. Assume a signal source resistance of 50 Ω on each input. (d) Will changing RC affect the amplifier CMRR? (e) Suggest two changes to this amplifier each of which would allow the CMRR to be increased. For each, give a reason why the change would have the desired effect.

Solution
0 0

For an NMOS differential pair, let VDD = VSS = 2.5 V, kn’W/L = 3 mA/V2, Vtn = 0.7 V, I = 0.2 mA, RD = 5 kΩ, and neglect channel-length modulation. With G2 grounded and vG1 = vid. Let vid be adjusted to the value that causes iD1 = 0.11 mA and iD2 = 0.09 mA. Find the corresponding values of vGS2, vs, vGS1, and hence vid. What is the difference output voltage vout = vD2 - vD1 ? What is the voltage gain (vD2 - vD1)/vid ? What value of vid results in iD1 = 0.09 mA and iD2 = 0.11 mA ?
Solution
0 0

a. For the circuit shown below, show a clean and labeled small signal equivalent circuit and derive the expression for vo/vb, (vb is the small signal voltage at the base node) vo/vsig, Rin and Rout. (b) This is the design part. The specifications are as follows: The required gain vo/vb = −120 V/V, Ic = 1 mA. and the require voltage swing at the output is ±3 V around the DC value of the output. (Hint: Do not use the generic design rule. You should be able to find the DC voltages at the collector and emitter from the specifications). Assume Vcc = 8 V. For this design assume VA = ∞ (this makes ro = ∞), V T (Thermal Voltage) = 25 mV, VBE = 0.7 V, VCEsat = 0.3 V and β = ∞. Find the values of RC, RE, RB1, and RB2. (c) If the β = 100 instead of the design value, find the new Ic. Now assuming VA = 50 V find vo/vsig, Rout and RIN. For this part assume Rsig = 10 kΩ. Punt: If you could not answer (b), use RC = 3 kΩ, RE = 2 kΩ, RB1 = 50 kΩ, and RG2 = 30 kΩ (d) Run a transient simulation of the designed circuit in Multisim. Use the same BJT used in the lab simulation. Show the input voltage v sig and output voltage v o on the same plot. Choose vsig to be at 1 kHz and 10 mV peak sinusoidal. Compare with calculated value of the gain in part c.
Solution
0 0