Question

Notify Me Bookmark

For the following amplifier, calculate the output voltage, VO, in V. IA = 0.7 mA VB = 1 V VC = 1 VR1 = 3 kΩ R2 = 5.1 kΩ R3= 23 kΩ R4 = 66 kΩ

For the following amplifier, calculate the output voltage, VO, in V. IA = 0.7 mA VB = 1 V VC = 1 VR1 = 3 kΩ R2 = 5.1 kΩ R3= 23 kΩ R4 = 66 kΩ

Image text
For the following amplifier, calculate the output voltage, VO, in V. IA = 0.7 mA VB = 1 V VC = 1 VR1 = 3 kΩ R2 = 5.1 kΩ R3= 23 kΩ R4 = 66 kΩ

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

Problem 2. Differential amplifier - current source load For the circuit in Fig. 2 (assume γ = 0), (b) Calculate minimum common-mode input, Vin, CM, if ISS requires at least 0.4 V across it. (c) For this value of Vin, CM , calculate maximum output voltage, Vout1,max and minimum output voltage Vout1,min that keeps transistors in saturation. Figure 2: Problem 2 NMOS: W = 10 μm, L = 0.5 μm, κn = 140 μA/V2, tox = 9 nm, μ0 = 350 cm2 /V/s, ϕ = 2ϕF = 0.9 V, Vt0 = 0.7 V, λ = 0.1 V−1( at L = 0.5 μm) and γ = 0.45(V). PMOS: W = 10 μm, L = 0.5 μm, κn = 40 μA/V2, tox = 9 nm, μ0 = 100 cm2 /V/s, ϕ = 2ϕF = 0.8 V, Vt0 = −0.8 V, λ = 0.2 V−1( at L = 0.5 μm) and γ = 0.4(V).

Solution
0 0

a. For the circuit shown below, show a clean and labeled small signal equivalent circuit and derive the expression for vo/vb, (vb is the small signal voltage at the base node) vo/vsig, Rin and Rout. (b) This is the design part. The specifications are as follows: The required gain vo/vb = −120 V/V, Ic = 1 mA. and the require voltage swing at the output is ±3 V around the DC value of the output. (Hint: Do not use the generic design rule. You should be able to find the DC voltages at the collector and emitter from the specifications). Assume Vcc = 8 V. For this design assume VA = ∞ (this makes ro = ∞), V T (Thermal Voltage) = 25 mV, VBE = 0.7 V, VCEsat = 0.3 V and β = ∞. Find the values of RC, RE, RB1, and RB2. (c) If the β = 100 instead of the design value, find the new Ic. Now assuming VA = 50 V find vo/vsig, Rout and RIN. For this part assume Rsig = 10 kΩ. Punt: If you could not answer (b), use RC = 3 kΩ, RE = 2 kΩ, RB1 = 50 kΩ, and RG2 = 30 kΩ (d) Run a transient simulation of the designed circuit in Multisim. Use the same BJT used in the lab simulation. Show the input voltage v sig and output voltage v o on the same plot. Choose vsig to be at 1 kHz and 10 mV peak sinusoidal. Compare with calculated value of the gain in part c.
Solution
0 0

Consider a two-stage amplifier shown below. Suppose that VB = 2V. All PMOS transistors are identical. Determine the small signal output resistance rout and the gain vout/vin. Transistor parameters: kp’ = μpCox = 50 uA/V^2, kn’ = μnCox = 100 uA/V^2, VAn = VAp = 25 V, VT,n = 1 V, VT,P = -1 V, WP2 = 32u, LP2 = 1u, WP3 = 80u, LP3 = 1u, Wn1 = 4u, Ln1 = 1u. In DC analysis, neglect the Early effect and use the following equation: ID = 1/2kp,n’W/L(VGS - VTp,n)^2. In small analysis you should consider the Early effect. To find the gain (vout/vin) of the amplifier, you need to find the gain of each stage.
Solution
0 0