Question

Notify Me Bookmark

For the MOSFET amplifier shown in figure Q1-A, is to be designed for the use in telephone circuit. It should work in the frequency range from 200 Hz to 3 KHz according to the given frequency response. Consider the transistor gm = 2mS, Determine value of the: i- Resistor RD ii- Capacitor Cc iii- Equivalent input capacitance Ci in case of fHi = fH.

For the MOSFET amplifier shown in figure Q1-A, is to be designed for the use in telephone circuit. It should work in the frequency range from 200 Hz to 3 KHz according to the given frequency response. Consider the transistor gm = 2mS, Determine value of the: i- Resistor RD ii- Capacitor Cc iii- Equivalent input capacitance Ci in case of fHi = fH.

Image text
For the MOSFET amplifier shown in figure Q1-A, is to be designed for the use in telephone circuit. It should work in the frequency range from 200 Hz to 3 KHz according to the given frequency response. Consider the transistor gm = 2mS, Determine value of the: i- Resistor RD ii- Capacitor Cc iii- Equivalent input capacitance Ci in case of fHi = fH.

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Login Sign Up

Similar/Related Questions

A differential amplifier with a single-ended output is shown below along with the MOSFET parameters. The amplifier is to be designed for a differential mode gain of 10 and a CMRR of 200 . The current source I must have a voltage drop VCS ≥ 1 volt. The voltage V0 = 0 when the MOSFET gates are at ground potential (Va = Vb = 0). Assume the current source I must have a voltage drop of at least Vcs, min = 1 V. MOSFET Parameters kn = 2×10−4 A/V2 Vt = 1 V;VA = 30 V a. Show that the single-ended differential gain can be expressed as Ad = gmro||RD/2 = Ad = kn I VDD(1 + VDD/VA). Hint: Express gm, RD, and ro as functions of the drain current 1 /2. b. Use the result of step #1 to find the required bias current I. c. What should be the value of RD ? d Find the required value of Rss. e. What is the maximum differential input voltage Vid for linear operation. f. What is the common mode input voltage range?
Solution
0 0

Figure 1 shows a single stage common source MOSFET amplifier circuit. We wish to design the circuit to meet the following design specifications: Load Resistance: RL = 100 KΩ Input Resistance: Ri > 200 KΩ Mid-band Gain: Gv = Vo/Vi = −50 ± 20% Supply Voltage: +15 Volts Circuit Capacitors: CG = 10μF; CS = 47μF; CD = 10μF Figure 1. Common Source MOSFET Amplifier Pre-lab: (a) Design the amplifier to meet the specifications above by choosing values for resistors R1, R2, RD and RS. Begin your design by choosing an appropriate value for the bias current ID. If ID ≈ 0.3 mA, assume VT ≈ 1.7 V, Kn ≈ 0.02 A/V2 and VA = 100 V(λ = 0.01 V−1). Find the small signal approximation of the input resistance Rin where Rin = R1∥R2 Find the small signal approximation of the output resistance Ro, where Ro is given as Ro = RD∥RL∥ro. The small signal mid-band gain of the amplifier is given by Gv = −gmRo where gm = 2knID = kn(VGS−VT) Once you choose ID the DC biasing of the transistor can be found using simple rules of thumb. The voltage VG should be approximately equal to VDD/3 > VT. For maximum symmetry, VD should be biased at the midpoint between VD(Max) and VD(Min). Clearly, the maximum VD is VDD and the minimum VD > VG−Vt. For example, if Vt = 1.7 V and VG = 1/3VDD = 5 V, then VD ≈ 9 V for maximum symmetry.

Figure 1 shows a single stage common source MOSFET amplifier circuit. We wish to design the circuit to meet the following design specifications: Load Resistance: RL = 100 KΩ Input Resistance: Ri > 200 KΩ Mid-band Gain: Gv = Vo/Vi = −50 ± 20% Supply Voltage: +15 Volts Circuit Capacitors: CG = 10μF; CS = 47μF; CD = 10μF Figure 1. Common Source MOSFET Amplifier Pre-lab: (a) Design the amplifier to meet the specifications above by choosing values for resistors R1, R2, RD and RS. Begin your design by choosing an appropriate value for the bias current ID. If ID ≈ 0.3 mA, assume VT ≈ 1.7 V, Kn ≈ 0.02 A/V2 and VA = 100 V(λ = 0.01 V−1). Find the small signal approximation of the input resistance Rin where Rin = R1∥R2 Find the small signal approximation of the output resistance Ro, where Ro is given as Ro = RD∥RL∥ro. The small signal mid-band gain of the amplifier is given by Gv = −gmRo where gm = 2knID = kn(VGS−VT) Once you choose ID the DC biasing of the transistor can be found using simple rules of thumb. The voltage VG should be approximately equal to VDD/3 > VT. For maximum symmetry, VD should be biased at the midpoint between VD(Max) and VD(Min). Clearly, the maximum VD is VDD and the minimum VD > VG−Vt. For example, if Vt = 1.7 V and VG = 1/3VDD = 5 V, then VD ≈ 9 V for maximum symmetry.
Solution
1 0

An NMOS amplifier is shown in Figure 1. Transistor M1 is biased in the saturation region for an amplifier application. The circuit is biased with a resistive voltage divider consisting of R1 and R2, a source degeneration resistor RS, and a load resistor RD. The drain bias current for the design is ID = 500 μA and VDS is 1.625 V. The device parameters are: L = 0.5 μm, W = 10 μm, kn’ = 200 μA/V2, Vtn = 0.5 V, and λn = 0. analyze the frequency response of the amplifier. a) Draw a midband small signal ac equivalent circuit model for the amplifier. For midband you can assume the reactance of Cin is sufficiently low that it is a short circuit. b) Derive an expression for the midband voltage gain transfer function Vout /Vsig. The amplified output signal is taken from the drain terminal and Vout = Vd. Write your gain function in terms of variables only. c) Evaluate the midband gain and calculate a value both in V/V and dB. d) Analyze the frequency response of the input network including the capacitor Cin. Find an expression for the transfer function H1(jω) = Vg/Vsig. e) Evaluate H1(jω) = Vg/Vsig and make a Bode plot of the magnitude of H1(jω). The x-axis is ω (log scale) and the y-axis is the magnitude in dB. f) Use the LTSPICE circuit template and verify the frequency response of the amplifier circuit. Include a copy of the schematic and the frequency response plot. Use 20 points per decade and a frequency span of 0.1 Hz to 100 Hz.
Solution
0 0