Question

Notify Me Bookmark

For the MOSFET shown in the figure the threshold voltage |Vtp| = 2 V and βp = 0.2 mA/V2. Assuming that both the transistors are in saturation, determine the value of ID. Hint: Find the voltage at X to determine the VGS of M1.

For the MOSFET shown in the figure the threshold voltage |Vtp| = 2 V and βp = 0.2 mA/V2. Assuming that both the transistors are in saturation, determine the value of ID. Hint: Find the voltage at X to determine the VGS of M1.

Image text
For the MOSFET shown in the figure the threshold voltage | V t p | = 2 V and β p = 0.2 m A / V 2 . Assuming that both the transistors are in saturation, determine the value of ID.
Hint: Find the voltage at X to determine the V G S of M 1 .

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

A current mirror circuit is shown in figure 10.2. The component/device parameters are given below as: Vdd = 1.2 V, Iref = 15 μA, VGS = 600 mV Vout = 700 mV Dimensions of M1: W1 = 2×120 nm and L1 = 60 nm Dimensions of M2: W2 = 2×120 nm and L2 = 60 nm Assume that both the devices are in saturation. It is given that λ = 0.9 V−1 for both transistors. Rest of the device parameters are identical for both the Fig10.2 transistors. 2) Q10.2: For the figure 10.2, find the absolute value of output current Iout (in μA) flowing through drain terminal of M2. Enter the closest answer (in μA) 2 points 3) Q10.3: For the circuit shown in figure 10.2, what is the drain to source small signal resistance of M2 in kΩ? Enter your answer (in kΩ) 2 points
Solution
0 0

For the circuit shown in Figure 2, VDD = 5 V, and transistors M1 and M2 have properties µnCox = 200µA/V2, (W/L) = 10, Vt0 = 0.7 V, and λ = 0. You may neglect the body effect below, unless you are specifically asked to consider it. Figure 2. Circuit for Problem 2. a) Draw the circuit above, and label the drain, gate, source, and bulk nodes for both transistors, using labels VD1, VG1, VS1, and VB1 for the drain, gate, source, and bulk nodes of device M1, respectively, and similarly for M2. In total, there should be 8 labels in your schematic. For this part, assume the transistors are in saturation. b) Determine the valid input range for the circuit under consideration; that is, determine the range on the input voltage Vin such that transistors M1 and M2 are operating in the saturation region. Note that, in your analysis, you are not constrained to Vin values between 0 V and VDD, inclusive; e.g., if Vin = 100 V keeps both of the transistors in saturation, then Vin = 100 V should be included in your range of valid input voltages. Your answer to this part should take the form Vin,low ≤ Vin ≤ Vin,high ; hopefully, it is obvious that you are being asked to provide numerical answers for the lower- and upper-bounds Vin,low and Vin,high , respectively. c) For the valid input range that you determined in part (b), determine the corresponding output voltage range; that is, determine Vout,low ≤ Vout ≤ Vout,high when the input is constrained to Vin,low ≤ Vin ≤ Vin,high. . As before, you should report numerical values for the lower- and upper-bounds Vout,low and Vout,high, , respectively. d) Determine the "on voltage" VON2 (or, as in the Sedra/Smith textbook, the "overdrive voltage") and drain current ID2 of transistor M2 over the range of valid input voltages. Also, determine the drain current ID1 of M1 over the valid input range. e) If you were to consider it, would any of the transistors in the circuit above be affected by the body effect? If "yes," then list the device (or, devices, as the case may be). Qualitatively speaking, how would your answers to parts (b) and (c) change if you were to take the body effect into account? Explain your reasoning.
Solution
0 0

(a) An enhancement n-MOS transistor has the following parameters: Threshold voltage VTh = 0.8 V, K′ = 20 μA/V2 = μnCox, where μn is mobility of electron, Cox gate oxide capacitance. (i) Find W/L ratio for gate voltage VG = 2.8 V, drain voltage, VD = 5 V, source voltage VS = 1 V and drain current ID = 0.24 mA. [6 marks] (ii) Calculate drain current ID for gate voltage VG = 5 V, drain voltage VD = 4 V, source voltage Vs = 2 V [4 marks] (b) For the n-channel EMOSFET used in circuit below, threshold voltage VTh = 1 V, K = 0.3 mA/V2. Find (i) V0 (as shown in figure below) [6 marks] (ii) If V0 = 2 V, find the new K value [4 marks] Fig. 3
Solution
0 0