Question

Notify Me Bookmark

In an automobile car, there is an adaptor that converts voltage from 12 volts to 5 volts for smart phone charging system. The adaptor consists of a zener diode with nominal voltage of 5.1 volts. The specification is given as: IZT = 20 mA, ZZT = 17 Ω, IZK = 0.25 mA, dan IZM = 40 mA. a. [5 points] Calculate maximum voltage that can be produced by the zener. b. [5 points] Calculate minimum R that prevents current on the zener excessive. c. [5 points] Calculate voltage on the zener when the power on load is maximum. d. [5 points] Calculate allowed maximum load power so that the voltage on the zener is not drop.

In an automobile car, there is an adaptor that converts voltage from 12 volts to 5 volts for smart phone charging system. The adaptor consists of a zener diode with nominal voltage of 5.1 volts. The specification is given as: IZT = 20 mA, ZZT = 17 Ω, IZK = 0.25 mA, dan IZM = 40 mA. a. [5 points] Calculate maximum voltage that can be produced by the zener. b. [5 points] Calculate minimum R that prevents current on the zener excessive. c. [5 points] Calculate voltage on the zener when the power on load is maximum. d. [5 points] Calculate allowed maximum load power so that the voltage on the zener is not drop.

Image text
In an automobile car, there is an adaptor that converts voltage from 12 volts to 5 volts for smart phone charging system. The adaptor consists of a zener diode with nominal voltage of 5.1 volts. The specification is given as:
I Z T = 20 m A , Z Z T = 17 Ω , I Z K = 0.25 m A , dan I Z M = 40 m A .
a. [5 points] Calculate maximum voltage that can be produced by the zener. b. [5 points] Calculate minimum R that prevents current on the zener excessive. c. [5 points] Calculate voltage on the zener when the power on load is maximum. d. [5 points] Calculate allowed maximum load power so that the voltage on the zener is not drop.

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

In this question, you are asked to find the effective transconductance (Gm) and the resistance into the drain (Rx) of a common-source amplifier with source degeneration. Based on the results, the voltage gain of a common-source amplifier with source degeneration will be evaluated a) The figures shown below are a circuit to find the effective transconductance (G) of the NMOSEFT with source degeneration (left) and its corresponding small-signal circuit (right). It is noted that the output is shorted to VDD (ac grounded) since the definition of effective transconductance is the ratio between the short-circuit output current and the input signal voltage. Prove that Gm is given by Gm = id/vin = gm/1+gmRs In this calculation, the current passing through ro can be neglected since, in general, ro is very large when the NMOSFET operates in saturation region and so this current is very small. Thus, the indication of id is the current of the voltage-controlled current source (gmvgs) only. b) The figure shown below is the method to evaluate the resistance looking into the drain (i.e. Rx) of a source-degenerated NMOSFET. The circuit is shown on the left while the equivalent small-signal modeling is shown on the right. It is noted that the bias condition (VBiAS) is set so that the values of gm and ro, can be defined. Moreover, there is no input signal (i.e. Vin = 0) since we would like to see the value of Rx which is due to the circuit only but not due to the external effect. Based on the above small-signal model, prove that RX = ro(1 + gmRS) The complete common-source amplifier with source degeneration is shown below. c) The complete common-source amplifier with source degeneration is shown below. Prove that the voltage gain of this amplifier is given by v. Vin Explain the reason(s) why the voltage gain is negative. What is the physical meaning of negative voltage gain?

In this question, you are asked to find the effective transconductance (Gm) and the resistance into the drain (Rx) of a common-source amplifier with source degeneration. Based on the results, the voltage gain of a common-source amplifier with source degeneration will be evaluated a) The figures shown below are a circuit to find the effective transconductance (G) of the NMOSEFT with source degeneration (left) and its corresponding small-signal circuit (right). It is noted that the output is shorted to VDD (ac grounded) since the definition of effective transconductance is the ratio between the short-circuit output current and the input signal voltage. Prove that Gm is given by Gm = id/vin = gm/1+gmRs In this calculation, the current passing through ro can be neglected since, in general, ro is very large when the NMOSFET operates in saturation region and so this current is very small. Thus, the indication of id is the current of the voltage-controlled current source (gmvgs) only. b) The figure shown below is the method to evaluate the resistance looking into the drain (i.e. Rx) of a source-degenerated NMOSFET. The circuit is shown on the left while the equivalent small-signal modeling is shown on the right. It is noted that the bias condition (VBiAS) is set so that the values of gm and ro, can be defined. Moreover, there is no input signal (i.e. Vin = 0) since we would like to see the value of Rx which is due to the circuit only but not due to the external effect. Based on the above small-signal model, prove that RX = ro(1 + gmRS) The complete common-source amplifier with source degeneration is shown below. c) The complete common-source amplifier with source degeneration is shown below. Prove that the voltage gain of this amplifier is given by v. Vin Explain the reason(s) why the voltage gain is negative. What is the physical meaning of negative voltage gain?

Solution
1 0

Q1. Consider the CMOS inverter of which the transistors have the following parameters: μnCox = 4μpCox = 160 μA/V2, ∣γ| = 0.5 V1/2, 2Φf = 0.5 V, λ = 0.001 V−1, Vtno = 0.6 V, Vtpo = −0.8 V, (W/L)n = 1 and (W/L)p = 4. The supply voltage VDD = 3.3 V. The capacitive load at the output node is 20 pF. The input voltage Vin is expected to be a perfect periodic square wave with full swing (low level : 0 V, high level: VDD). (a) Calculate tl, the time required for the output voltage Vout to change from 0 V to the threshold voltage of the inverter, using the average-current method. (b) Write the expression of calculation of t2, the time required for the output voltage Vout to change from 2.9 V to the 0.4 V, using the analytical method (integral). Then calculate t2 using the average-current method. (c) Determine the maximum frequency of the periodic square wave input so that the output signal will have a full swing in each cycle. (d) Calculate the peak value of in, the NMOS transistor current, during the transition, and its average value over a clock cycle T. (The average value here is not the same as the average-current in the "average-current method" for delay estimation) (e) If the capacitive load is now changed to be 250 pF, what can be done to make tl and t2 unchanged?
Solution
0 0

A double pulse test circuit, as shown below, has a DC-link voltage, VDC = 100 V and the inductor has a value of L = 200 μH. At t = 0, a gate-source voltage, vgs = 20 V is applied to the MOSFET, which is enough to turn it on. The vgs = 20 V is applied for the time period Ton after which it is turned down to vgs = 0 V for the time period Tof. There is no initial current stored in the inductor prior to t = 0. Describe what is the purpose of the double pulse test circuit, and what information can be derived from the use of the circuit? Explain the purpose of the diode in the double pulse test circuit, and what happens if it is removed? Sketch the currents iL, is and iD as a function of time. Calculate the time Ton required for the inductor current (iL) to be 20 A at the end of t = Ton Calculate how much energy is stored in the inductor L at t = Ton The MOSFET has a thermal resistance junction-to-case, Rsc = 0.8 K/W, case-to-heatsink Rcs = 1.2 K/W and heatsink-toambient RsA = 4 K/W. For a maximum junction temperature of TJ max = 175∘C and ambient temperature TA = 50∘C, what is the maximum allowed power dissipation ?

Solution
0 0