Question

Notify Me Bookmark

In In the circuit below of Figure Q.12, a MOSFET for which VN = 0.5 V and ka = 0.3 mAV2. Find the value of input voltage V1 so that output voltage Vout = 1.5 V [3 Marks]

In In the circuit below of Figure Q.12, a MOSFET for which VN = 0.5 V and ka = 0.3 mAV2. Find the value of input voltage V1 so that output voltage Vout = 1.5 V [3 Marks]

Image text
In In the circuit below of Figure Q.12, a MOSFET for which V N = 0.5 V and k a = 0.3 m A V 2 . Find the value of input voltage V 1 so that output voltage Vout=1.5V [3 Marks]

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

The following circuit diagram shows the use of two such MOS transistors for the implementation of a fundamental logic gate in digital ICs. Both MOS transistors (M1 & M2) have the same threshold voltage VT = 0.5 V and µCox = 10-4 A/V2. Fig. 2.1 (a). What are the operation modes of the MOS transistors (MI&M2) when the input is a logic “low” signal (i.e. Vin = 0 V )? (b). Find out the expression of the current flowing through the MOS transistor M2 as a function of the output voltage Vout. Then determine the current when Vout = 1.5 V. (c). Using results in (a) and (b) as a hint, hence or otherwise, determine VOH (i.e. the maximum output voltage when the output is a logic “high” signal). (d). Based on the results in (b) and (c), hence or otherwise, describe two advantages of digital circuits with CMOS implementation compared with the implementation in Fig. 2.1. (e). Draw a schematic circuit diagram of the CMOS implementation of the logic circuit in Fig. 2.1. You must use standard circuit symbols and show the signal interconnections clearly with proper labels.
Solution
0 0

A transistor schematic diagram of a digital circuit is shown below (Fig. 3.1). The sizes of the MOS transistors are given as ratio (W/L)n = 4 and (W/L)p = 2. |It is also given that |VTn| = VTp = 0.5 V and µnCox = 10-4 A/V2 while µpCox = 5 × 10-5 A/V2 . Fig. 3.1 (a). Draw the logic gate symbol of the above CMOS digital circuit. (2 marks) (b). Sketch the output waveform Vout for the given input voltage signals VA and VB. Assume that the logic circuit is fast enough to respond to the given input waveform. Voltage levels and any other key features must be labelled properly. (8 marks) (c). If both the inputs VA and VB are connected to VDD, determine the equivalent resistance linking the output to ground. (7 marks) (e). If the inputs VA and VB are tied together, sketch a graph of the output voltage Vout as a function of VA from 0 V to 1.8 V in the static case. Any turning point(s) or important features (e.g. voltage levels) as well as axes must be shown clearly or labelled explicitly. (8 marks)
Solution
0 0

Consider the circuit configuration shown below, which is commonly used for measuring n-channel MOSFET parameters. The transistor's length and width are 1 μm. The accompanying graph plots the transistor's square root of drain current vs. gate voltage, VG. a) Estimate the threshold voltage of the n-channel MOSFET. b) When VG is between 1.5 V and 2.5 V, in what region is the device operating? Consider the p-channel MOSFET amplifier given to the right. ID = 12 kp(VSG − |Vtp|)2, VDD = 5 V, RL = 2 kΩ, kp = 1 mA/V2, Vtp = −1 V c) Derive an expression for the transistor bias point, VGQ, as a function of VDD, Ra, and Rb. d) Determine the required ratio Ra/Rb such that the MOSFET current, ID = 0.5 mA e) What is the voltage bias point of the output VoutQ? Use the value(s) from part d. Please show all steps. A_ = 0.5 VB = Saturation C = VoD(Rb/(Ra+Rb))D = Ra/Rb = 2/3 E = 1 V)

Solution
0 0