Question

Notify Me Bookmark

In the TTL circuit in Figure below, the transistor parameters IOL = 40 mA, IOH = 10 mA and IIH = 0.1 mA, VBE sat = 0.8 V and VCEsat = 0.1 V : 1- Write the truth table of the circuit showing the values of logic “0” and Logic “1”. 2- Calculate the fan out NL and NH, which one you select as a circuit fan-out?

In the TTL circuit in Figure below, the transistor parameters IOL = 40 mA, IOH = 10 mA and IIH = 0.1 mA, VBE sat = 0.8 V and VCEsat = 0.1 V : 1- Write the truth table of the circuit showing the values of logic “0” and Logic “1”. 2- Calculate the fan out NL and NH, which one you select as a circuit fan-out?

Image text
In the TTL circuit in Figure below, the transistor parameters IOL = 40 mA, IOH = 10 mA and IIH = 0.1 mA, VBE sat = 0.8 V and VCEsat = 0.1 V : 1- Write the truth table of the circuit showing the values of logic “0” and Logic “1”. 2- Calculate the fan out NL and NH, which one you select as a circuit fan-out?

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

Consider the shown circuit Part 1: Hand Calculation Assume that VBE(on) = 0.7 V, VBE( sat ) = 0.8 V, VCE( sat ) = 0.1 V, forward βF = 25, reveres βR = 0.1, a) Fill in the table below, what is the logic gate? Vx Vx Qx Qx Q1 Q2 Q Vout 0.1 V 0.1 V 0.1 V 5 V 5 V 0.1 V 5 V 5 V b) Assume a 10k load resistor is connected calculate Vout and the output current if: Vx = Vx = 0.1 V Vx = Vy = 5 V c) Calculate the power drawn from the supply volt-age VCC if: Vx = Vx = 0.1 V Vx = Vx = 5 V Part 2: Simulation Draw the circuit on LTSpice a) Verify the results obtained in part (a) of the hand calculation using DC operating point analysis b) Set Vx = 0 V and use DC sweep analysis varying Vy from 0 to 5 V. Draw the voltage transfer characteristics (VTC) c) Set Vx=0V, and set Vy to be a pulse with the parameters: Vinitial = 0, Von=5, Tdelay = 2 ns, Trise = 1 ns, Tfall = 1 ns, Ton=5ns, and perform transient analysis for 10ns, plot Vy and Vout and measure the delays tpHL and tpLH (measure the delays from the start of the input pulse to the point when Vout reaches VOH or VOL) Notes: Homework submission is through the Moodle platform Submit a single compressed file containing: The hand calculations Screenshot showing the circuit and the simulation results The schematic file (.asc) The netlist file (.net)
Solution
2 0

Consider the following TTL circuit. Assume that the transistor parameters are that βF = 50, βR = 0.1 (for each emitter input), VBE( on ) = 0.7 V, VBE( sat ) = 0.8 V and VCE( sat ) = 0.1 V a) (15) Calculate the maximum fanout when vA = vB = 5 V. b) (15) Calculate the power dissipation when vA = vB = 5 V.
Solution
0 0

The circuit shown in Figure 7 is supposed to work as an inverter where it has the following values for its parameters: VDD = 1.8V, lambda_1 = lambda_2 = 0, unCox = 100 uA/V2, upCox = 50 uA/V2, VTH,N=0.4V, VTH,P= -0.5V. (W/L)2 = 3/0.18 1. Assuming that vout,min = 0.1 V when vin = VDD, determine the mode of the transistors M1 and M2. 2. Using the previous results, determine the value of (W/L)1 that will guarantee that vout, min = 0.1 V, when vin = VDD.

The circuit shown in Figure 7 is supposed to work as an inverter where it has the following values for its parameters: VDD = 1.8V, lambda_1 = lambda_2 = 0, unCox = 100 uA/V2, upCox = 50 uA/V2, VTH,N=0.4V, VTH,P= -0.5V. (W/L)2 = 3/0.18 1. Assuming that vout,min = 0.1 V when vin = VDD, determine the mode of the transistors M1 and M2. 2. Using the previous results, determine the value of (W/L)1 that will guarantee that vout, min = 0.1 V, when vin = VDD.

Solution
0 0