Question

Notify Me Bookmark

Label the voltage swing (max and min voltage) at each node connected to a box, given that the inputs to the system vary between two states: A = 2.5 V and B = 0 V and A = 0 V and B = 2.5 V Assume the threshold voltage is 0.5 volt, and Vdd is 2.5 V unless marked.

Label the voltage swing (max and min voltage) at each node connected to a box, given that the inputs to the system vary between two states: A = 2.5 V and B = 0 V and A = 0 V and B = 2.5 V Assume the threshold voltage is 0.5 volt, and Vdd is 2.5 V unless marked.

Image text
Label the voltage swing (max and min voltage) at each node connected to a box, given that the inputs to the system vary between two states: A = 2.5 V and B = 0 V and A = 0 V and B = 2.5 V Assume the threshold voltage is 0.5 volt, and Vdd is 2.5 V unless marked.

Detailed Answer

1 0

Please enter your email here. You will get email when this question is answered by our tutor.

Answer
Doubtrix Logo

This Problem has been solved!

You'll get a detailed, step-by-step and expert verified solution.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Login Sign Up
  • Student Reviews:
  • (1)
  • Correct answers (1)
  • Complete solution (1)
  • Step-by-step solution (1)
  • Fully explained (1)

Similar/Related Questions

Given the following circuit, assuming that all inputs of the circuit shown in Figure 1 below are initially 0 during the precharge phase and that all internal nodes are at 0V: a. Calculate the voltage drop on V0, if A changes to 1 (VDD = 2.5 V) during the evaluate phase. It is given that Vtn = 0.5 V, 2φF = 0.6 V and γ = 0.4 V0.5 . Hint: Don’t forget the body effect. b. Now calculate the voltage drop on Vo if both A and B change to 1 (under the above conditions). c. What is the maximum number of transistors that can be connected in series to M1 and M2 (including M1 and M2, excluding M0 ) if the output should not fall below 0.9 V during the evaluate phase? Assume that each one of the new transistors has the same intrinsic capacitance (to ground) as M1 and M2 (C=10fF).
Solution
1 0

In the dynamic logic circuit shown below, all the transistors have the minimum channel length, and their sizes (widths) are marked. The inverter at the output is a standard static CMOS inverter with a PMOS size of 2 and an NMOS size of 1 . For a unit-sized NMOS or PMOS transistor, the intrinsic capacitance at its drain or source terminal is CD, and the capacitance at its gate is CG. For unit-sized NMOS and PMOS transistors, their onresistances are RN and RP, respectively. CD = CG = 1 fF and RP = 2 RN = 2 kΩ. (a) Express y as a Boolean function of the inputs A, B, C and D in the evaluation phase (CLK = 1). (b) Find the capacitances at nodes y, a, b and c, respectively. (c) Let A = B = D = 1 and C = 0 and suppose nodes a, b and c are at 0 V in the pre-charge phase (CLK = 0). Estimate the time it takes for the voltage at y to decrease from VDD to VDD/2 in the evaluation phase. (d) Repeat (c) if nodes a, b and c are at VDD in the pre-charge phase. (e) If the inputs are C = 1 and A = B = D = 0 and suppose nodes a, b and c are at 0 V in the pre-charge phase. Considering the charge sharing effect, what is the voltage at node y in the evaluation phase? It is known VDD = 2.5 V, VTN = 0.5 V and the body effect of the transistors can be ignored.

Solution
0 0

Given the following circuit, assume that all of the circuit’s inputs are initially zero during the pre-charge phase and that all internal nodes are at 0 V. 1. Calculate the voltage drop on V0, if A changes to 1 (VDD = 2.5 V) during the evaluate phase. It is given that Vtn 0 = 0.5 V, 2ϕF = 0.6 V, and γ = 0.4 V1/2. Hint: Don’t forget the body effect. 2. Now calculate the voltage drop on Vo if both A and B change to 1 (under the above conditions). Determine the maximum number of transistors that can be connected in series to M1 and M2 (including M1 and M2, excluding M0) if the output should not fall below 0.9 V during the evaluate phase. Assume that each one of the new transistors has the same intrinsic capacitance (to ground) as M1 and M2 (C=10fF).
Solution
0 0