Question

Notify Me Bookmark

Required information A resistive load inverter in two logic states is given as follows: Let VTN = 0.6 V. For the circuit shown in the figure, VL = 0.5 V, VH = 2.6 V, VDD = 2.6 V, Kn′ = 100 μA/V2, VDS = 0.5, VTN = 0.6 V and power P = 0.0001 W. Find the new values of R and (W/L)S assuming that the power dissipation remains the same?

Required information A resistive load inverter in two logic states is given as follows: Let VTN = 0.6 V. For the circuit shown in the figure, VL = 0.5 V, VH = 2.6 V, VDD = 2.6 V, Kn′ = 100 μA/V2, VDS = 0.5, VTN = 0.6 V and power P = 0.0001 W. Find the new values of R and (W/L)S assuming that the power dissipation remains the same?

Image text
Required information A resistive load inverter in two logic states is given as follows:
Let V T N = 0.6 V .
For the circuit shown in the figure, V L = 0.5 V , V H = 2.6 V , V D D = 2.6 V , K n ′ = 100 μ A / V 2 , V D S = 0.5 , V T N = 0.6 V and power P = 0.0001 W.
Find the new values of R and (W/L)S assuming that the power dissipation remains the same?

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

Assume VTN = 0.7 V, Kn = 100 μA/V2, VL = 0.2 V Design the NMOS resistive load inverter for operation at a power level of 0.30 mW with VDD = 3.3 V. What is the size of Ms and the value of R? What is the significance of the product K, R in inverter design. Should it be high or low? What are the values for NM and NMI? Find Ron of the NMOS transistor. Verify your design by using this resistance in the voltage division. For an inverter design, what factors determine the values of VL, VDD and power level.

Solution
0 0

Given the following circuit, assuming that all inputs of the circuit shown in Figure 1 below are initially 0 during the precharge phase and that all internal nodes are at 0V: a. Calculate the voltage drop on V0, if A changes to 1 (VDD = 2.5 V) during the evaluate phase. It is given that Vtn = 0.5 V, 2φF = 0.6 V and γ = 0.4 V0.5 . Hint: Don’t forget the body effect. b. Now calculate the voltage drop on Vo if both A and B change to 1 (under the above conditions). c. What is the maximum number of transistors that can be connected in series to M1 and M2 (including M1 and M2, excluding M0 ) if the output should not fall below 0.9 V during the evaluate phase? Assume that each one of the new transistors has the same intrinsic capacitance (to ground) as M1 and M2 (C=10fF).
Solution
1 0

Consider the NMOS inverter with depletion load in Figure 16.7(a). Let VDD = 1.8 V, and assume VTND = 0.3 V and VTNL = -0.6 V. (a) Design the circuit such that the power dissipation is 80μW and the output voltage is vO = 0.06 V when vI is a logic 1. (b) Using the results of part (a), determine the transition points for the driver and load transistors. (c) If (W/L)D found in part (a) is doubled, what is the maximum power dissipation in the inverter and what is vO when vI is a logic 1? The NMOS inverter with depletion load is shown in Figure 16.7(a). The bias is VDD = 2.5 V. The transistor parameters are VTND = 0.5 V and VTNL = -1 V. The width-to-length ratio of the load device is W/L = 1. (a) Design the driver transistor such that vO = 0.05 V when the input is a logic 1. (b) What is the power dissipated in the circuit when vI = 2.5 V?

Consider the NMOS inverter with depletion load in Figure 16.7(a). Let VDD = 1.8 V, and assume VTND = 0.3 V and VTNL = -0.6 V. (a) Design the circuit such that the power dissipation is 80μW and the output voltage is vO = 0.06 V when vI is a logic 1. (b) Using the results of part (a), determine the transition points for the driver and load transistors. (c) If (W/L)D found in part (a) is doubled, what is the maximum power dissipation in the inverter and what is vO when vI is a logic 1? The NMOS inverter with depletion load is shown in Figure 16.7(a). The bias is VDD = 2.5 V. The transistor parameters are VTND = 0.5 V and VTNL = -1 V. The width-to-length ratio of the load device is W/L = 1. (a) Design the driver transistor such that vO = 0.05 V when the input is a logic 1. (b) What is the power dissipated in the circuit when vI = 2.5 V?
Solution
0 0