Question

Notify Me Bookmark

The MOSFET in the below circuit has k = 1 mA/V2, Vt = 1 V. In what mode is the MOSFET operating? Saturation Region Active Region Triode Region Cut-off Region None of them

The MOSFET in the below circuit has k = 1 mA/V2, Vt = 1 V. In what mode is the MOSFET operating? Saturation Region Active Region Triode Region Cut-off Region None of them

Image text
The MOSFET in the below circuit has k = 1 m A / V 2 , V t = 1 V . In what mode is the MOSFET operating? Saturation Region Active Region Triode Region Cut-off Region None of them

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

Problem 2.1: The N-channel enhancement type MOSFET in the following circuit has kn′ = 200 μA/V2, W/L = 20 /0.18, Vt = 0.6 V and λ = 0.1 V−1. Find the mode of its operation and the drain current in the following cases: (i) VG = 1 V and VD = 0.2 V and (ii) VG = 1 V and VD = 2 V. Key formulae: Cut-off condition VGS < Vt; current ID = 0 Linear region conditions VGS > Vt and VGD > Vt; current ID = kn′WL[(VGS − Vt)VDS − 12 VDS2] Saturation conditions VGS > Vt and VGD < Vt; current ID = 12 kn′WL(VGS − Vt)2(1 + λVDS) Solution: Case (i) VGS = and VGD = hence the mode of operation is ID = Problem 2.2: What is the mode of operation of the transistor in each of the following circuits? Take Vt = −0.8 V Note: Identify the type of the MOSFET transistor and take into account the change of the sign for all the voltages when you check the conditions for cut-off, linear mode and saturation. Solution:
Solution
0 0

The MOSFET in the circuit of Fig. below has Vt = 1 V and kn = 2 mA/V2, and the Early effect can be neglected. a) Find the values of Rs and RD that result in the MOSFET operating with an overdrive voltage of 0.5 V and a drain voltage of 1.5 V. What is the resulting ID value? b) If RL is reduced from 15 kohm, to 10 kohm, what does VD become? c) If RL is disconnected, what does VD become? d) With RL disconnected, what is the largest RD that can be used while the MOSFET is remaining in saturation?
Solution
0 0

(a) For the circuit shown in figure 1(a), find the following [20] i. Vi(s)/Vs(s) ii. Vo(s)/Vi(s) iii. Vo(s)/Vs(s) iv. Draw the magnitude plot for |T(jω)| in dBvs. frequency v. Lower 3 dB cut-off frequency fL vi. Upper 3 dB cut-off frequency fH vii. Bandwidth (b) Consider the n-channel MOSFET amplifier in figure 1(b). ID = 12 kn′W L(VGS − Vt)2, VDD = 5 V, RL = 2 kΩ, kn′WL = 1 mA/V2, Vt = 1 V. You can ignore channel length modulation. CC is the input coupling capacitor. You can assume it is infinitely large. [10] i. Determine the required ratio RA/RB such that the MOSFET gm = 1 mA/V. Remember that gm is defined as ∂ID/∂VGS ii. Draw the small-signal π model for the amplifier iii. Calculate the gain Vout/Vin (for gm = 1 mA/V ) (a) Figure for question 1 (a) (b) Figure for question 1 (b)

Solution
0 0