Question

Notify Me Bookmark

The transistor shown in the circuit below must be biased by a collector current IC = 1 mA and VBE = 0.75 V. Knowing that β = 100, find RB without making any approximation Select one: a. RB = 14.2 kΩ b. RB = 53.8 kΩ c. None of these d. RB = 77 kΩ

The transistor shown in the circuit below must be biased by a collector current IC = 1 mA and VBE = 0.75 V. Knowing that β = 100, find RB without making any approximation Select one: a. RB = 14.2 kΩ b. RB = 53.8 kΩ c. None of these d. RB = 77 kΩ

Image text
The transistor shown in the circuit below must be biased by a collector current I C = 1 m A and V B E = 0.75 V . Knowing that β = 100 , find R B without making any approximation
Select one: a. R B = 14.2 k Ω b. R B = 53.8 k Ω c. None of these d. R B = 77 k Ω

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

Question: For the AC equivalent circuit of a common-emitter BJT amplifier shown in Figure 1, assume that VCC = 10 V, VBE = 0.7 V, RS = 5 kΩ, RB = 100 kΩ, RL = 1 kΩ, Cb'e = 2 pF, Ccb′ = 1 pF, and CL = 1 pF. Assume bias current IB = 25 μA, Boltzmann's constant k = 1.38×10−23 J/K, q = 1.6 ×10−19 C, T = 300 K, VT = 26 mV, β = 100, rbb' = 100 Ω, and ignore ro. Assuming the equivalent noise bandwidth is 100 kHz, and neglecting the flicker noise and capacitive effect. Note: For the BJT biased on the forward active region: rπ = VT/IB, gm = IC/VT. (a) Calculate the total equivalent input rms noise voltage and current by looking into node a. (b) Calculate the total equivalent input rms noise voltage and current by looking into node b. (c) Discuss if a transformer (with turn ratio I:N) can be incorporated into point b to minimize the total input referred noise? If yes, what is the N to be? Figure 1
Solution
0 0

Electronics 2 - Homework 2 Second semester 2023-2024 Solve the following questions, and verify your solution using LTSpice. simulation. For each question you need to:Solve the question by handProvide a screenshot of the circuitProvide a screenshot confirming the hand calculations Note that you can change the BJT parameter Beta by adding a SPICE directive and changing the parameter BF Question 1: BJT transistors The parameters for each transistor in the figure below are β = 80, and VBE(m) = 0.7 V. Determine all the voltages and currents in the circuit. Circuit for question 1 Question 2: Amplifier Configurations The signal source in the circuit below is vs = 5 sin⁡(100000πt)mV. The transistor parameters are β = 120, and the capacitors are 10 μF (a) Design the circuit such that IC = 0.25 mA and VCE = 3 V. (b) Find the open circuit voltage gain Avo (c) Find the input resistance Rin (from the base of the transistor) (d) Find the output resistance (e) Use the amplifier model (Avo, Rin, Ro) to find vo(t). Circuit for question 2 Question 3: Amplifier Configurations Consider the circuit shown. The transistor current gain β = 180. and the source signal has a frequency of 100 kHz and the capacitors are 10 μF Note that the current source is replaced by an open circuit in the small signal model equivalent circuit. Determine: (a) the voltage gain from source to load, (b) the input resistance seen by the source (c) the output resistance

Solution
0 0

To improve the performance of the differential amplifier shown in Figure Q1, the biasing current source is replaced by a Widlar current source. The collector resistors are replaced by a current mirror formed by the matched bipolar transistors Qs and Q6, and the bipolar transistors Q1 and Q2 are replaced by the matched field-effect transistors M1 and M2. A single-sided output at the drain terminal of M2 is used. The transistor parameters for the bipolar transistors are: β = 100, VBE (on) = VEB(on) = 0.7 V, and VA = 100 V. The transistor parameters for M1 and M2 are: Kn = 0.15 mA/V2, VT N = 0.8 V, λ = 0.01 V-1 . The improved differential amplifier is shown in Figure Q2. (a) Determine the quiescent voltages and currents of M1 and M2 when v1 = v2 = 0. (4 marks) (b) Design the value of resistor RE such that IQ = 0.1 mA. (2 marks) (c) Determine the maximum and minimum common-mode voltages that can be applied to v1 and v2. (3 marks) (d) Determine the percentage change in IQ when the common-mode voltage applied to v1 and v2 changes from the maximum to the minimum value obtained in part (c). (5 marks) (c) Define vd = v1 - v2, determine the differential-mode voltage gain Ad of the improved differential amplifier.
Solution
0 0