Question

Notify Me Bookmark

Verify the operations of current mirror circuit by LTSpice simulation. 5.1 (5 point) Create the following MOSFET current mirrow schematic, assigning the parameters and label the X and Y nodes (Hints: For M1, you need to "mirror" NMOS4). For M1 and M2: kn = 200 u vT0 = 0.5 W1 = W2 = 50 u L1 = L2 = 10 u IREF = 50 uA VDD = 5 V

Verify the operations of current mirror circuit by LTSpice simulation. 5.1 (5 point) Create the following MOSFET current mirrow schematic, assigning the parameters and label the X and Y nodes (Hints: For M1, you need to "mirror" NMOS4). For M1 and M2: kn = 200 u vT0 = 0.5 W1 = W2 = 50 u L1 = L2 = 10 u IREF = 50 uA VDD = 5 V

Image text
  1. Verify the operations of current mirror circuit by LTSpice simulation. 5.1 (5 point) Create the following MOSFET current mirrow schematic, assigning the parameters and label the X and Y nodes (Hints: For M1, you need to "mirror" NMOS4). For M1 and M2:
k n = 200 u v T 0 = 0.5 W 1 = W 2 = 50 u L 1 = L 2 = 10 u I R E F = 50 u A V D D = 5 V

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions
Solution
0 0

Consider the circuit shown in Figure 1; note that the numerical value of Vbias is not needed for this problem. Figure 1. Circuit for Problem 1. Here, current source Ibias = 13mA and NMOS devices M1 and M2 have the following properties: • W1 = W2 = 13µm, L1 = L2 = 1µm, kn’ = 500µA/V2 , and VT = 1 V. • The body effect and channel-length modulation effect for devices M1 and M2 should be neglected for this problem. a) If VDD = 5V, determine the numerical value of output current Iout. . Show your work and include appropriate units with your numerical answer. b) If VDD = 5V, determine the numerical value of node voltage Vx. Show your work and include appropriate units with your numerical answer. c) Determine VDDmin, the minimum numerical value of VDD which ensures that device M2 is in saturation. Show your work and include appropriate units with your numerical answer.
Solution
0 0

The MOS transistors have the following characteristics: nMOS:Vtn = 0.7 V, Kn′ = 200 μA/V2. Assume VDD = 5 V. The required current ID1 = 100 μA the output voltage ( Vout) should be allowed to swing to a low of 0.2 V and the DC value of VOUT = 2.5 volts. Also design for current IREF = 50 μA. (a) Find the (W/L) ratio of all transistors and (ii) the resistor R. For this part you may assume there is no channel length modulation. ( 25 points). (b) Show a clean and labeled small signal equivalent circuit with the values shown. Assume all transistors have |λ| = 0.02 V1 (10 points) (c) Find both an expression and the numerical value for the small signal gain vo/vin, and Rout . 15 points)
Solution
0 0