Question

Notify Me Bookmark

Voltage Transfer Function These are the parameters of NMOS and PMOS transistor, μnCox = 2.5μpCox = 20 μA V2, |Vtn| = |Vtp| = 1 V, (W L)n = (W L)p = 30 μm 10 μm for the circuit given below. Do the following a) Find the region NMOS and PMOS operating b) Find the voltage Vout. c) Find the current Id. d) By keeping the (W L)n same find the new (W L)p which will ensure Vout = 1.5 V Ignore the body effect. Figure 3 CMOS based circuit

Voltage Transfer Function These are the parameters of NMOS and PMOS transistor, μnCox = 2.5μpCox = 20 μA V2, |Vtn| = |Vtp| = 1 V, (W L)n = (W L)p = 30 μm 10 μm for the circuit given below. Do the following a) Find the region NMOS and PMOS operating b) Find the voltage Vout. c) Find the current Id. d) By keeping the (W L)n same find the new (W L)p which will ensure Vout = 1.5 V Ignore the body effect. Figure 3 CMOS based circuit

Image text
  1. (20 Points) Voltage Transfer Function These are the parameters of NMOS and PMOS transistor, μ n C o x = 2.5 μ p C o x = 20 μ A V 2 , | V t n | = | V t p | = 1 V , ( W L ) n = ( W L ) p = 30 μ m 10 μ m for the circuit given below. Do the following a) Find the region NMOS and PMOS operating b) Find the voltage Vout. c) Find the current Id. d) By keeping the ( W L ) n same find the new ( W L ) p which will ensure Vout = 1.5 V Ignore the body effect. Figure 3 CMOS based circuit

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

For the amplifier below, following design information is provided: VDD = 3.3 V, R = 2.4 kΩ, ISS = 1.8 mA, k1 = k2 = 5 mA/V2, VTH,1 = VTH,2 = 0.5 V, λ = 0.1 V−1, γ = 0, ki′ = μ0Cox, ki = μ0 Cox(W L)i. Assume that both transistors are identical and in the saturation region. Finally, NMOS and PMOS bulk terminals are connected to the ground and VDD, respectively. a) What is the DC bias voltage for M1 and M2 given that the voltage drop across ISS is 0.4 V ? You can neglect the channel length modulation, here. Check that the transistors are in the correct operation-mode. b) The resistors will be realized using identical PMOS transistors M3 and M4. If the transistors to be used will have k3 = k4 = 1.5 mA/V2, what will be their overdrive voltages? Check that the transistors are in the correct operation-mode. c) What is the differential voltage gain AV,diff = Vout/Vid in dB ? d) ISS will be realized as a cascode current source. Assume that the voltage drop of 0.4 V is equally shared by the two transistors, M5 and M6 having k5′ = k6′ = 0.5 mA/V2 and VTH, 5 = VTH, 6 = 0.5 V. Assuming the gate voltages of both transistors are 1 V, find the W/L ratios of each device. Once again, you can neglect the channel length modulation here. e) Considering (d), how would the W/L ratios qualitatively change (increase/decrease/stays the same), if γ > 0 ? Explain your reasoning analytically, i. e. , using appropriate equations. f) Using the cascode current source, calculate the common-mode gain of the circuit AV, CM = Vout /Vin in dB, where Vin . s applied to the gates of both M1 and M2. Assume λ = 0.1 V−1 for M5 and M6. g) Calculate the CMRR of the circuit in dB.
Solution
0 0

Q1. Consider the CMOS inverter of which the transistors have the following parameters: μnCox = 4μpCox = 160 μA/V2, ∣γ| = 0.5 V1/2, 2Φf = 0.5 V, λ = 0.001 V−1, Vtno = 0.6 V, Vtpo = −0.8 V, (W/L)n = 1 and (W/L)p = 4. The supply voltage VDD = 3.3 V. The capacitive load at the output node is 20 pF. The input voltage Vin is expected to be a perfect periodic square wave with full swing (low level : 0 V, high level: VDD). (a) Calculate tl, the time required for the output voltage Vout to change from 0 V to the threshold voltage of the inverter, using the average-current method. (b) Write the expression of calculation of t2, the time required for the output voltage Vout to change from 2.9 V to the 0.4 V, using the analytical method (integral). Then calculate t2 using the average-current method. (c) Determine the maximum frequency of the periodic square wave input so that the output signal will have a full swing in each cycle. (d) Calculate the peak value of in, the NMOS transistor current, during the transition, and its average value over a clock cycle T. (The average value here is not the same as the average-current in the "average-current method" for delay estimation) (e) If the capacitive load is now changed to be 250 pF, what can be done to make tl and t2 unchanged?
Solution
0 0

ajiv Gandhi University of Knowledge Technologics (Department of Electronics and Communication Engineering) MONTHLY TEST - 2 Year/Sem: E2-SEMII Subject: AEC Subject Code:23 EC2101 Date: 17-10-2023 Time: 45 Minutes Max. Marks: 15 Marks Section-A ― Answer the following question. (1 X7 = 7 Marks)a) For the common source amplifier as shown in fig below, Given μaCnt(W/L) = 0.25 mA/V2, Vm = 1.5 V, VA = 50 v (use VA for riscalculation (x≠0) then. Find MILLER'S THEOREM i) small signal voltage gain ii) input resistance and output resistance iii) maximum allowable imput signal (OR)For the Differential amplifier as shown in fig below, Given μ2 Cin = 100 μA/V2, Vti = 1 V, +VDD = +5 V, −VSS = −5 V; Neglect Channel length modulation. Assume M1 and M2 are matched(identical) transistors. find V1, V2 and V3 for the following cases a) (W/L)1 = (W/L)2 = 20 b) (W/L)1 = 1.5(W/L)2 = 20; Section-B Answer the following question. (1 8 = 8 Marka)a)for the MOSFETS shown in circuit μ3 Cm = 50 μA/V2, Vm = 1 V, L = 1. μm, w = 10 μm then find the V 3 and 13 in the circuit. b) For the Differential amplifier given below, Given μnCn = 1 mA/V2, Vn

Solution
0 0