Question

Notify Me Bookmark

A student has a 26.0 μF capacitor and a variable frequency AC source. Determine the following. (a) frequencies (in Hz) for which the capacitor has a reactance below 380 Ω f ≥ Hz (b) reactances (in Ω ) of a 37.0 μF capacitor over this same frequency range xC ≤ Ω

A student has a 26.0 μF capacitor and a variable frequency AC source. Determine the following. (a) frequencies (in Hz) for which the capacitor has a reactance below 380 Ω f ≥ Hz (b) reactances (in Ω ) of a 37.0 μF capacitor over this same frequency range xC ≤ Ω

Image text
A student has a 26.0 μ F capacitor and a variable frequency AC source. Determine the following. (a) frequencies (in H z ) for which the capacitor has a reactance below 380 Ω
f ≥ ◻ H z
(b) reactances (in Ω ) of a 37.0 μ F capacitor over this same frequency range
x C ≤ ◻ Ω

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

A student has a 82.0 μH inductor, a 82.0 μF capacitor, and a variable frequency AC source. Determine the source frequency (in kHz ) at which the inductor and capacitor have the same reactance. kHz
Solution
0 0

In the figure shown below, one end of a cord is attached to the floor and the other end is attached to a small set of essentially massless wheels through a slot in a track on which the wheels roll without friction. As a result of this arrangement, the upper end of the cord is essentially free. At equilibrium, the cord is vertical and motionless. When it carries a small amplitude wave, the cord is under a uniform tension of 1.20 N. The cord has a mass of 5.80 g and a length of 85.0 cm. (a) Find the speed (in m/s) of the transverse waves in the cord. m/s (b) The cord's vibration possibilities are a set of standing-wave states, each with a node at the fixed bottom end and an antinode at the free top end. Find the node-antinode distances (in m) for the first three harmonics. Enter your answers from the lowest to the highest harmonic. m m m (c) Find the frequency (in Hz) of each of these states. (Enter your answers from simplest to more complicated.) Hz Hz Hz (d) What If? The wheels get stuck on the track and are unable to move, hence making the cart stationary. Determine the node-antinode distance (in m) and frequency of vibration (in Hz) for the third harmonic. distance m frequency Hz
Solution
0 0

In this amplifier circuit, the high and low DC voltage sources are: VDD = 5 V and VSS = −5 V respectively. Consider that all three external capacitors have high values. The PMOS transistor has a threshold voltage equal to Vt = −1 V and kp = kp′(W/L) = 0.4 mA/V2, and the NMOS transistor has a threshold voltage Vt = 1 V and a kn = kn′(W/L) = 2 mA/V2. It was shown in HW#7 that the DC drain voltage of the PMOS transistor is −0.2 V and the DC source of the NMOS transistor is −2 V. a) Perform the small signal analysis of this circuit and determine the voltage gain: AV = Vo/Vi b) Determine the input and output resistance of this amplifier Rin and Rout . c) Discuss what is the purpose of the part of the circuit between CC2 and CC3 which includes the NMOS transistor in this amplifier design. d) Determine the parameters of a simple voltage amplifier model (discussed in chapter 1) which will represent this amplifier. Note that the parameters of the simple voltage amplifier excludes any series resistance of the external source ( Vi ) (in this case it is zero anyway) and the load resistance (in this case RL = 2 kΩ ). e) Using the simple model from part (c) determine the voltage gain AV = Vo/Vi and see if it agrees with the answer of part (a). VDD
Solution
0 0