Question

Notify Me Bookmark

A student has a 82.0 μH inductor, a 82.0 μF capacitor, and a variable frequency AC source. Determine the source frequency (in kHz ) at which the inductor and capacitor have the same reactance. kHz

A student has a 82.0 μH inductor, a 82.0 μF capacitor, and a variable frequency AC source. Determine the source frequency (in kHz ) at which the inductor and capacitor have the same reactance. kHz

Image text
A student has a 82.0 μ H inductor, a 82.0 μ F capacitor, and a variable frequency AC source. Determine the source frequency (in k H z ) at which the inductor and capacitor have the same reactance. k H z

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

A student has a 26.0 μF capacitor and a variable frequency AC source. Determine the following. (a) frequencies (in Hz) for which the capacitor has a reactance below 380 Ω f ≥ Hz (b) reactances (in Ω ) of a 37.0 μF capacitor over this same frequency range xC ≤ Ω

Solution
0 0

In this amplifier circuit, the high and low DC voltage sources are: VDD = 5 V and VSS = −5 V respectively. Consider that all three external capacitors have high values. The PMOS transistor has a threshold voltage equal to Vt = −1 V and kp = kp′(W/L) = 0.4 mA/V2, and the NMOS transistor has a threshold voltage Vt = 1 V and a kn = kn′(W/L) = 2 mA/V2. It was shown in HW#7 that the DC drain voltage of the PMOS transistor is −0.2 V and the DC source of the NMOS transistor is −2 V. a) Perform the small signal analysis of this circuit and determine the voltage gain: AV = Vo/Vi b) Determine the input and output resistance of this amplifier Rin and Rout . c) Discuss what is the purpose of the part of the circuit between CC2 and CC3 which includes the NMOS transistor in this amplifier design. d) Determine the parameters of a simple voltage amplifier model (discussed in chapter 1) which will represent this amplifier. Note that the parameters of the simple voltage amplifier excludes any series resistance of the external source ( Vi ) (in this case it is zero anyway) and the load resistance (in this case RL = 2 kΩ ). e) Using the simple model from part (c) determine the voltage gain AV = Vo/Vi and see if it agrees with the answer of part (a). VDD
Solution
0 0

Consider the shown circuit, where R = 500 Ω, L = 40 μH, C = 30 nF, and Vs is a sinusoidal source with a peak amplitude of 5 V. (Vs(t) = 5 cos⁡(ωt)V) Part 1: Hand Calculation a) Assume the source has a frequency of 140 kHz, calculate: the impedance Z seen by the source (expressed as a complex number and as magnitude/phase). Is the impedance capacitive or inductive? the source current Is. (Expressed as a Phasor and as a time function)the voltage Vo (Expressed as a Phasor and as a time function) b) Repeat part (a) at a frequency of 148 kHz c) Calculate the resonant frequency of the circuit (the frequency at which the reactive components cancel each other) d) find the impedance of the circuit at the resonant frequency e) Calculate the Quality factor and the 3-dB bandwidth of the circuit. Note that the resonator (LC circuit) is parallel Part 2: Simulation Draw the circuit on LTSpice a) Perform AC analysis (from 130 kHz to 170 kHz, use linear scale with 10000 points) and plot the following on a separate plot: The voltage (Vo)The current (Is)The impedance seen by the source b) From the plots verify your results in the hand calculation for parts (a) and (b) c) from the plots find the resonant frequency d) From the voltage plot, find the 3-dB bandwidth. Notes: The default Y-scale for AC analysis in LTSpice is dB, you can change it to linear To plot the impedance, add a trace and plot the expression of V over I Homework submission is through the Moodle platform Submit a single compressed file containing: The hand calculations Screenshot showing the circuit and the simulation results The schematic file (.asc)The netlist file (.net)

Solution
0 0