Question

Notify Me Bookmark

(a) What is the resistance of a lightbulb that uses an average power of 75.0 W when connected to a 60.0 Hz power source having a maximum voltage of 160 V? Ω (b) What is the resistance of a 110 W bulb? Ω

(a) What is the resistance of a lightbulb that uses an average power of 75.0 W when connected to a 60.0 Hz power source having a maximum voltage of 160 V? Ω (b) What is the resistance of a 110 W bulb? Ω

Image text
(a) What is the resistance of a lightbulb that uses an average power of 75.0 W when connected to a 60.0 H z power source having a maximum voltage of 160 V ? ◻ Ω (b) What is the resistance of a 110 W bulb? ◻ Ω

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

D *7.121 The MOSFET in the circuit of Fig. P7.121 has Vt = 0.8 V, kn = 5 mA/V2, and VA = 40 V. (a) Find the values of RS, RD, and RG so that ID = 0.4 mA, the largest possible value for RD is used while a maximum signal swing at the drain of ±0.8 V is possible, and the input resistance at the gate is 10 MΩ. Neglect the Early effect. Figure P7.120 (b) Find the values of g m and r o at the bias point. (c) If terminal Z is grounded, terminal X is connected to a signal source with a resistance of 1 MΩ, and terminal Y is connected to a load resistance of 10 kΩ, find the voltage gain from signal source to load. (d) If terminal Y is grounded, find the voltage gain from X to Z with Z open-circuited. What is the output resistance of the source follower?
Solution
0 0

The model of a voltage Amplifier is shown below connected to a small signal source vs having a series resistance Rs and to a load resistor RL. a) If the amplifier's input resistance (Ri) is 100 kΩ, what is the range of values that the series resistance Rs can have if we wish 90% or more of the small signal source signal to be coupled into the amplifier. b) If the amplifier's output resistance (Ro) is 2 kΩ What is the range of values that the load resistance RL can have if we wish 90% or more of the amplifier's dependent voltage source voltage to be delivered (i. e. dropped) to the load resistor.
Solution
0 0

SRAM (static random access memory): This problem concerns the design of a 4-resistor 2-transistor (BJT) SRAM cell (flip-flop) having a supply voltage of VCC = 5.0 V. Assume that the BJT's CE saturation voltage (VCE,sat) in the ON state is 0.2 V. Assume that the current amplification of the transistors is β = 50. (a) Draw the circuit diagram. (b) Choose one of the two stable states of the flip-flop, and indicate all circuit elements that consume power. Circle these circuit elements. (c) Write an equation for the power consumed by each of these circuit elements (circled under the previous question). Sum up all these powers (summands) to obtain the total power consumed by the circuit. Which of these summands represents the greatest power? Give the approximate power consumed by the circuit by writing an equation that has just the dominant summand. (d) Design a 4-resistor 2-transistor SRAM circuit in which the dominant power-consuming circuit element consumes a power of about 1 μW. What is the collector current? Suggest numerical values for the resistances of all four resistors. (e) What would be the power consumed by a 1 Gbit SRAM circuit using the memory cell you just designed? Do you have any comments on the result?
Solution
0 0