Question

Notify Me Bookmark

Calculate the effective resistance of a pocket calculator that has a 1.35-V battery and through which 0.200 mA flows. 6.750 k Ohm 4.750 k Ohm 5.750 k Ohm 5.650 k Ohm

Calculate the effective resistance of a pocket calculator that has a 1.35-V battery and through which 0.200 mA flows. 6.750 k Ohm 4.750 k Ohm 5.750 k Ohm 5.650 k Ohm

Image text
Calculate the effective resistance of a pocket calculator that has a 1.35-V battery and through which 0.200 mA flows. 6.750 k Ohm 4.750 k Ohm 5.750 k Ohm 5.650 k O h m

Detailed Answer

2 0

Please enter your email here. You will get email when this question is answered by our tutor.

Answer
Doubtrix Logo

This Problem has been solved!

You'll get a detailed, step-by-step and expert verified solution.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Login Sign Up
  • Student Reviews:
  • (2)
  • Correct answers (2)
  • Complete solution (2)
  • Fully explained (1)

Similar/Related Questions

Q2-(25 pts) A variable resistor, R, whose value ranges from 0 to ∞ is connected between the terminals of a battery that has an emf ε = 18.0 V, and an internal resistance of 4.00 Ω. The ammeter and voltmeter are idealized meters. a) (8 pts.) As R varies over its full range of values, what will be the largest and smallest readings of the voltmeter and ammeter? Justify each answer with statement and/or direct calculation below. b) (8 pts.) The power dissipated at the variable resistor is 18.0 W. What can be the maximum reading on the voltmeter in this case? c) (9 pts.) Suppose we replace the variable resistor with a cylindrical wire of length 8.0 cm and cross section diameter 0.5 cm. The voltmeter reads 15.0 V. Calculate resistivity of the cylindrical wire, the magnitudes of the current density and the electric field through the wire. V18W = J = E = ρ =
Solution
0 0

Consider an n-type MOSFET, which consists of a 10 nm thick oxide (er = 3.9) and has a gate length of 1 micron, a gate width of 20 micron and a threshold voltage of 1.5 Volt. Calculate the resistance of the MOSFET in the linear region as measured between source and drain when applying a gate-source voltage of 3 Volt. What should the gate-source voltage be to double the resistance? The surface mobility of the electrons is 300 cm2/V-sec.
Solution
0 0

a) Your job is to design the following circuit, using 2 mA of bias current and achieve a gain of at least 3.5 V/V. You realize that you can bias an amplifier using degeneration resistance using the circuit topology shown below. Calculate values for RS to get 2 mA of current, and RL to get the gain you need. For large signal calculations, you may assume lambda = 0. What is the problem with this amplifier? b) You suggest replacing the load resistance RL with a current source that has a very large output impedance, as shown below. The current source requires a headroom of at least 0.5 V. What is the gain of the amplifier? How does this fix the problem from the previous part? 1 Debugging Amplifiers Suppose you are given an NMOS transistor with the following parameters: In addition, VDD = 5 V.

a) Your job is to design the following circuit, using 2 mA of bias current and achieve a gain of at least 3.5 V/V. You realize that you can bias an amplifier using degeneration resistance using the circuit topology shown below. Calculate values for RS to get 2 mA of current, and RL to get the gain you need. For large signal calculations, you may assume lambda = 0. What is the problem with this amplifier? b) You suggest replacing the load resistance RL with a current source that has a very large output impedance, as shown below. The current source requires a headroom of at least 0.5 V. What is the gain of the amplifier? How does this fix the problem from the previous part? 1 Debugging Amplifiers Suppose you are given an NMOS transistor with the following parameters: In addition, VDD = 5 V.

a) Your job is to design the following circuit, using 2 mA of bias current and achieve a gain of at least 3.5 V/V. You realize that you can bias an amplifier using degeneration resistance using the circuit topology shown below. Calculate values for RS to get 2 mA of current, and RL to get the gain you need. For large signal calculations, you may assume lambda = 0. What is the problem with this amplifier? b) You suggest replacing the load resistance RL with a current source that has a very large output impedance, as shown below. The current source requires a headroom of at least 0.5 V. What is the gain of the amplifier? How does this fix the problem from the previous part? 1 Debugging Amplifiers Suppose you are given an NMOS transistor with the following parameters: In addition, VDD = 5 V.
Solution
1 0