Question

Notify Me Bookmark

How tall must a water-filled manometer be to measure blood pressure as high as 300 mmHg? Density of blood is 1.05×103 kg/m3 4.08 m 1.36 m 5.05 m 7.60 m

How tall must a water-filled manometer be to measure blood pressure as high as 300 mmHg? Density of blood is 1.05×103 kg/m3 4.08 m 1.36 m 5.05 m 7.60 m

Image text
How tall must a water-filled manometer be to measure blood pressure as high as 300 m m H g ?
Density of blood is 1.05 × 10 3 k g / m 3 4.08 m 1.36 m 5.05 m 7.60 m

Detailed Answer

0 0

Please enter your email here. You will get email when this question is answered by our tutor.

Doubtrix Logo

Problem is not yet solved!

Click on Notify me to get email when question is answered.

Join Doubtrix with 7-days free trial

  • Icon Correct & Verified Answers
  • Icon No AI-Generated Answers
  • Icon Video Solution for Difficult Questions
  • Icon Work With Experts to Reach at Correct Answers
Notify me Login Sign Up

Similar/Related Questions

Bob has just finished climbing a sheer cliff above a beach and wants to figure out how high he climbed. All he has to use, however, is a baseball, a stopwatch, and a friend on the ground with a long measuring tape. Bob is a pitcher, and knows that the fastest he can throw the ball is v0 = 76.0 mph, Bob starts the stopwatch as he throws the ball (with no way to measure the ball's initial trajectory) and watches carefully. The ball rises and then falls, and after t1 = 0.910 s, the ball is once again level with Bob. Bob cannot see well enough to time when the ball hits the ground. Bob's friend then measures that the ball landed a distance of x = 376 ft. from the base of the cliff. The gravitational acceleration in imperial units is 32.2 f/s2. How tall hc is the cliff if Bob threw the ball from exactly 5 ft above the cliff edge? hc =
Solution
0 0

(a) An engineer was measuring the high-frequency C−V characteristic of a MOS capacitor with a ptype substrate and 100Å thick gate oxide. In order to measure the maximum depletion region width in the inversion mode (threshold voltage = 2 V), he swept the gate voltage, VG, from -4 V to +4 V. At VG = +4 V, he recorded the capacitance value (C1) while keeping the voltage constant. However, after reading the C1 value, he found that the C1 value was increasing with time and finally settled to another value C2. In this case, is his estimated maximum depletion width based on the C1 value reliable? Explain your answer. Why does this situation happen? What parameter must be adjusted in the measurement to avoid this situation? (10 pts) (b) Figure Q1.1 is the capacitance-voltage characteristic of a MOS structure on p-type substrate, measured at 1 MHz. In this measurement, a MOS transistor is used and the source, the drain, and the substrate terminals are grounded. Is this result reasonable? Explain. (15 pts) Fig. Q1.1
Solution
0 0

To demonstrate the ideas of electric current and resistivity the following experiment was conducted using a 10.0 m long 1.00 m diameter pipe. The pipe is connected to an air pump which produces high air pressure at one end. The other end of the pipe is open to the surrounding air, and the pump maintains a constant difference in air pressure between the two ends. Six hundred electrically charged ping pong balls are injected into the pipe with velocities that have random magnitudes and directions. Due to the difference in air pressure, the balls drift from the high pressure end of the pipe to the low pressure end at a speed of 2.00 cm/s. If every ping pong ball is given a charge of 6.00 microcoulombs, how much current flows through the pipe?
Solution
1 0